30 C.F.R. Subpart C—Fire Prevention and Control
Title 30 - Mineral Resources
Authority: Sec. 101, Federal Mine Safety and Health Act of 1977, Pub. L. 91–173, as amended by Pub. L. 95–164, 91 Stat. 1291 (30 U.S.C. 811).
The following definitions apply in this subpart. Flash point. The minimum temperature at which sufficient vapor is released by a liquid to form a flammable vapor-air mixture near the surface of the liquid. Safety can. A container of not over five gallons capacity that is designed to safely relieve internal pressure when exposed to heat and has a spring-closing lid and spout cover. [50 FR 4054, Jan. 29, 1985, as amended at 68 FR 32361, May 30, 2003; 69 FR 38840, June 29, 2004] Abandoned electric circuits shall be deenergized and isolated so that they cannot become energized inadvertently. No person shall smoke or use an open flame where flammable or combustible liquids, including greases, or flammable gases are— (a) Used or transported in a manner that could create a fire hazard; or (b) Stored or handled. Readily visible signs prohibiting smoking and open flames shall be posted where a fire or explosion hazard exists. Flammable or combustible liquid spillage or leakage shall be removed in a timely manner or controlled to prevent a fire hazard. Internal combustion engines shall be switched off before refueling if the fuel tanks are integral parts of the equipment. This standard does not apply to diesel-powered equipment. (a) Waste materials, including liquids, shall not accumulate in quantities that could create a fire hazard. (b) Until disposed of properly, waste or rags containing flammable or combustible liquids that could create a fire hazard shall be placed in covered metal containers or other equivalent containers with flame containment characteristics. (a) If a hazard to persons could be created, no combustible materials shall be stored or allowed to accumulate within 25 feet of the following: (1) Electric substations. (2) Unburied, flammable or combustible liquid storage tanks. (3) Any group of containers used for storage of more than 60 gallons of flammable or combustible liquids. (b) The area within the 25-foot perimeter shall be kept free of dry vegetation.
Title 30: Mineral Resources
PART 56—SAFETY AND HEALTH STANDARDS—SURFACE METAL AND NONMETAL MINES
Subpart C—Fire Prevention and Control
§ 56.4000 Definitions.
§ 56.4011 Abandoned electric circuits.
Prohibitions/Precautions/Housekeeping
§ 56.4100 Smoking and use of open flames.
§ 56.4101 Warning signs.
§ 56.4102 Spillage and leakage.
§ 56.4103 Fueling internal combustion engines.
§ 56.4104 Combustible waste.
§ 56.4130 Electric substations and liquid storage facilities.
Firefighting Equipment
§ 56.4200 General requirements.
(a) For fighting fires that could endanger persons, each mine shall have—
(1) Onsite firefighting equipment for fighting fires in their early stages; and
(2) Onsite firefighting equipment for fighting fires beyond their early stages, or the mine shall have made prior arrangements with a local fire department to fight such fires.
(b) This onsite firefighting equipment shall be—
(1) Of the type, size, and quantity that can extinguish fires of any class which could occur as a result of the hazards present; and
(2) Strategically located, readily accessible, plainly marked, and maintained in fire-ready condition.
[50 FR 4054, Jan. 29, 1985, as amended at 50 FR 20100, May 14, 1985]
§ 56.4201 Inspection.
(a) Firefighting equipment shall be inspected according to the following schedules:
(1) Fire extinguishers shall be inspected visually at least once a month to determine that they are fully charged and operable.
(2) At least once every twelve months, maintenance checks shall be made of mechanical parts, the amount and condition of extinguishing agent and expellant, and the condition of the hose, nozzle, and vessel to determine that the fire extinguishers will operate effectively.
(3) Fire extinguishers shall be hydrostatically tested according to Table C–1 or a schedule based on the manufacturer's specifications to determine the integrity of extinguishing agent vessels.
(4) Water pipes, valves, outlets, hydrants, and hoses that are part of the mine's firefighting system shall be visually inspected at least once every three months for damage or deterioration and use-tested at least once every twelve months to determine that they remain functional.
(5) Fire suppression systems shall be inspected at least once every twelve months. An inspection schedule based on the manufacturer's specifications or the equivalent shall be established for individual components of a system and followed to determine that the system remains functional. Surface fire suppression systems are exempt from these inspection requirements if the systems are used solely for the protection of property and no persons would be affected by a fire.
(b) At the completion of each inspection or test required by this standard, the person making the inspection or test shall certify that the inspection or test has been made and the date on which it was made. Certifications of hydrostatic testing shall be retained until the fire extinguisher is retested or permanently removed from service. Other certifications shall be retained for one year.
Table C-1_Hydrostatic Test Intervals for Fire Extinguishers------------------------------------------------------------------------ Test Extinguisher type interval (years)------------------------------------------------------------------------Soda Acid.................................................... 5Cartridge-Operated Water and/or Antifreeze................... 5Stored-Pressure Water and/or Antifreeze...................... 5Wetting Agent................................................ 5Foam......................................................... 5AFFF (Aqueous Film Forming Foam)............................. 5Loaded Stream................................................ 5Dry-Chemical with Stainless Steel Shells..................... 5Carbon Dioxide............................................... 5Dry-Chemical, Stored Pressure, with Mild Steel Shells, Brazed 12 Brass Shells, or Aluminum Shells............................Dry-Chemical, Cartridge or Cylinder Operated, with Mild Steel 12 Shells......................................................Bromotrifluoromethane_Halon 1301............................. 12Bromochlorodifluoromethane_Halon 1211........................ 12Dry-Powder, Cartridge or Cylinder-Operated, with Mild Steel 12 Shells\1\...................................................------------------------------------------------------------------------\1\ Except for stainless steel and steel used for compressed gas cylinders, all other steel shells are defined as ``mild steel'' shells.
§ 56.4202 Fire hydrants.If fire hydrants are part of the mine's firefighting system, the hydrants shall be provided with— (a) Uniform fittings or readily available adapters for onsite firefighting equipment; (b) Readily available wrenches or keys to open the valves; and (c) Readily available adapters capable of connecting hydrant fittings to the hose equipment of any firefighting organization relied upon by the mine. § 56.4203 Extinguisher recharging or replacement.Fire extinguishers shall be recharged or replaced with a fully charged extinguisher promptly after any discharge. § 56.4230 Self-propelled equipment.(a)(1) Whenever a fire or its effects could impede escape from self-propelled equipment, a fire extinguisher shall be on the equipment. (2) Whenever a fire or its effects would not impede escape from the equipment but could affect the escape of other persons in the area, a fire extinguisher shall be on the equipment or within 100 feet of the equipment. (b) A fire suppression system may be used as an alternative to fire extinguishers if the system can be manually activated. (c) Fire extinguishers or fire suppression systems shall be of a type and size that can extinguish fires of any class in their early stages which could originate from the equipment's inherent fire hazards. Fire extinguishers or manual actuators for the suppression system shall be located to permit their use by persons whose escape could be impeded by fire. Firefighting Procedures/Alarms/Drills§ 56.4330 Firefighting, evacuation, and rescue procedures.(a) Mine operators shall establish emergency firefighting, evacuation, and rescue procedures. These procedures shall be coordinated in advance with available firefighting organizations. (b) Fire alarm procedures or systems shall be established to pomptly warn every person who could be endangered by a fire. (c) Fire alarm systems shall be maintained in operable condition. § 56.4331 Firefighting drills.Emergency firefighting drills shall be held at least once every six months for persons assigned firefighting responsibilities by the mine operator. Flammable and Combustible Liquids and Gases§ 56.4400 Use restrictions.(a) Flammable liquids shall not be used for cleaning. (b) Solvents shall not be used near an open flame or other ignition source, near any source of heat, or in an atmosphere that can elevate the temperature of the solvent above the flash point. § 56.4401 Storage tank foundations.Fixed, unburied, flammable or combustible liquid storage tanks shall be securely mounted on firm foundations. Piping shall be provided with flexible connections or other special fittings where necessary to prevent leaks caused by tanks settling. § 56.4402 Safety can use.Small quantities of flammable liquids drawn from storage shall be kept in safety cans labeled to indicate the contents. § 56.4430 Storage facilities.(a) Storage tanks for flammable or combustible liquids shall be— (1) Capable of withstanding working pressures and stresses and compatible with the type of liquid stored; (2) Maintained in a manner that prevents leakage; (3) Isolated or separated from ignition sources to prevent fire or explosion; and (4) Vented or otherwise constructed to prevent development of pressure or vacuum as a result of filling, emptying, or atmospheric temperature changes. Vents for storage of Class I, II, or IIIA liquids shall be isolated or separated from ignition sources. These pressure relief requirements do not apply to tanks used for storage of Class IIIB liquids that are larger than 12,000 gallons in capacity. (b) All piping, valves, and fittings shall be— (1) Capable of withstanding working pressures and stresses; (2) Compatible with the type of liquid stored; and (3) Maintained in a manner that prevents leakage. (c) Fixed, unburied tanks located where escaping liquid could present a hazard to persons shall be provided with— (1) Containment for the entire capacity of the largest tank; or (2) Drainage of a remote impoundment area that does not endanger persons. However, storage of only Class IIIB liquids does not require containment or drainage to remote impoundment. Installation/Construction/Maintenance§ 56.4500 Heat sources.Heat sources capable of producing combustion shall be separated from combustible materials if a fire hazard could be created. § 56.4501 Fuel lines.Fuel lines shall be equipped with valves capable of stopping the flow of fuel at the source and shall be located and maintained to minimize fire hazards. This standard does not apply to fuel lines on self-propelled equipment. § 56.4502 Battery-charging stations.(a) Battery-charging stations shall be ventilated with a sufficient volume of air to prevent the accumulation of hydrogen gas. (b) Smoking, use of open flames, or other activities that could create an ignition source shall be prohibited at the battery charging station during battery charging. (c) Readily visible signs prohibiting smoking or open flames shall be posted at battery-charging stations during battery charging. § 56.4503 Conveyor belt slippage.Belt conveyors within confined areas where evacuation would be restricted in the event of a fire resulting from belt-slippage shall be equipped with a detection system capable of automatically stopping the drive pulley. A person shall attend the belt at the drive pulley when it is necessary to operate the conveyor while temporarily bypassing the automatic function. § 56.4530 Exits.Buildings or structures in which persons work shall have a sufficient number of exits to permit prompt escape in case of fire. § 56.4531 Flammable or combustible liquid storage buildings or rooms.(a) Storage buildings or storage rooms in which flammable or combustible liquids, including grease, are stored and that are within 100 feet of any person's work station shall be ventilated with a sufficient volume of air to prevent the accumulation of flammable vapors. (b) In addition, the buildings or rooms shall be— (1) Constructed to meet a fire resistance rating of at least one hour; or (2) Equipped with an automatic fire suppression system; or (3) Equipped with an early warning fire detection device that will alert any person who could be endangered by a fire, provided that no person's work station is in the building. (c) Flammable or combustible liquids in use for day-to-day maintenance and operational activities are not considered in storage under this standard. Welding/Cutting/Compressed Gases§ 56.4600 Extinguishing equipment.(a) When welding, cutting, soldering, thawing, or bending— (1) With an electric arc or with an open flame where an electrically conductive extinguishing agent could create an electrical hazard, a multipurpose dry-chemical fire extinguisher or other extinguisher with at least a 2–A:10–B:C rating shall be at the worksite. (2) With an open flame in an area where no electrical hazard exists, a multipurpose dry-chemical fire extinguisher or equivalent fire extinguishing equipment for the class of fire hazard present shall be at the worksite. (b) Use of halogenated fire extinguishing agents to meet the requirements of this standard shall be limited to Halon 1211 (CBrClF2) and Halon 1301 (CBrF3). When these agents are used in confined or unventilated areas, precautions based on the manufacturer's use instructions shall be taken so that the gases produced by thermal decompostion of the agents are not inhaled. § 56.4601 Oxygen cylinder storage.Oxygen cylinders shall not be stored in rooms or areas used or designated for storage of flammable or combustible liquids, including grease. § 56.4602 Gauges and regulators.Gauges and regulators used with oxygen or acetylene cylinders shall be kept clean and free of oil and grease. § 56.4603 Closure of valves.To prevent accidental release of gases from hoses and torches attached to oxygen and acetylene cylinders or to manifold systems, cylinder or manifold system valves shall be closed when— (a) The cylinders are moved; (b) The torch and hoses are left unattended; or (c) The task or series of tasks is completed. § 56.4604 Preparation of pipelines or containers.Before welding, cutting, or applying heat with an open flame to pipelines or containers that have contained flammable or combustible liquids, flammable gases, or explosive solids, the pipelines or containers shall be— (a) Drained, ventilated, and thoroughly cleaned of any residue; (b) Vented to prevent pressure build-up during the application of heat; and (c)(1) Filled with an inert gas or water, where compatible; or (2) Determined to be free of flammable gases by a flammable gas detection device prior to and at frequent intervals during the application of heat. Appendix I to Subpart C of Part 56—National Consensus StandardsMine operators seeking further information in the area of fire prevention and control may consult the following national consensus standards. |
------------------------------------------------------------------------ MSHA standard National consensus standard------------------------------------------------------------------------§§ 56.4200, 56.4201.... NFPA No. 10_Portable Fire Extinguisher. NFPA No. 11_Low Expansion Foam and Combined Agent Systems. NFPA No. 11A_High Expansion Foam Systems. NFPA No. 12_Carbon Dioxide Extinguishing Systems. NFPA No. 12A_Halon 1301 Extinguishing Systems. NFPA No. 13_Water Sprinkler Systems. NFPA No. 14_Standpipe and Hose Systems. NFPA No. 15_Water Spray Fixed Systems. NFPA No. 16_Foam Water Spray Systems. NFPA No. 17_Dry-Chemical Extinguishing Systems. NFPA No. 121_Mobile Surface Mining Equipment. NFPA No. 291_Testing and Marketing Hydrants. NFPA No. 1962_Care, Use, and Maintenance of Fire Hose, Connections, and Nozzles.§ 56.4202................... NFPA No. 14_Standpipe and Hose Systems. NFPA No. 291_Testing and Marketing Hydrants.§ 56.4203................... NFPA No. 10_Portable Fire Extinguishers.§ 56.4230................... NFPA No. 10_Portable Fire Extinguishers. NFPA No. 121_Mobile Surface Mining Equipment.------------------------------------------------------------------------
Browse Previous |
Browse Next
|
