30 C.F.R. Subpart T—Safety Standards for Methane in Metal and Nonmetal Mines
Title 30 - Mineral Resources
Authority: 30 U.S.C. 811.
Source: 52 FR 24941, July 1, 1987, unless otherwise noted.
This subpart T sets forth procedures and safety standards for each metal and nonmetal underground mine subject to the Federal Mine Safety and Health Act of 1977. All metal and nonmetal mines will be placed into one of the categories or subcategories defined in this subpart. Mines shall operate in accordance with the applicable standards in this subpart to protect persons against the hazards of methane gas and dust containing volatile matter. The standards in this subpart apply to underground mines as well as surface mills at Subcategory I-C mines. These mines are also required to be operated in accordance with the other applicable health and safety standards published in 30 CFR part 57. The following definitions apply in this subpart: Competent person. A person designated by the mine operator who has sufficient experience and training to perform the assigned task. Explosive material. Explosives, blasting agents, and detonators. Explosives are substances classified as explosives by the Department of Transportation in §§173.53, 173.88, and 173.100 of Title 49 of the Code of Federal Regulations (1986 Edition). Blasting agents are substances classified as blasting agents by the Department of Transportation in §173.114(a) of Title 49 of the Code of Federal Regulations (1986 Edition). Detonators are devices containing a detonating charge used to initiate explosives. Examples of detonators are blasting caps, electric or non-electric instantaneous or delay blasting caps and delay connectors. [A copy of Title 49 is available at any Metal and Nonmetal Mine Safety and Health District Office of the Mine Safety and Health Administration]. Substantial construction. Construction of such strength, material, and workmanship that the object will withstand air blasts, blasting shock, ground movement, pressure differentials, wear, and usage which may be expected to occur in the mining environment. [52 FR 24941, July 1, 1987, as amended at 69 FR 38842, June 29, 2004]
Title 30: Mineral Resources
PART 57—SAFETY AND HEALTH STANDARDS—UNDERGROUND METAL AND NONMETAL MINES
Subpart T—Safety Standards for Methane in Metal and Nonmetal Mines
General
§ 57.22001 Scope.
§ 57.22002 Definitions.
Mine Categorization
§ 57.22003 Mine category or subcategory.
(a) All underground mines, and the surface mills of Subcategory I-C mines (gilsonite), shall be placed into one of the following categories or subcategories to protect persons against the hazards of methane and dusts containing volatile matter. Categories and subcategories are defined as follows:
(1) Category I applies to mines that operate within a combustible ore body and either liberate methane or have the potential to liberate methane based on the history of the mine or the geological area in which the mine is located. Category I is divided into Subcategories I-A, I-B, and I-C as follows:
(i) Subcategory I-A applies to mines that operate within a combustible ore body and liberate methane and in which—
(A) A concentration of 0.25 percent or more methane has been detected in the mine atmosphere and confirmed by laboratory analysis; or
(B) An ignition of methane has occurred.
(ii) Subcategory I-B applies to mines that operate within a combustible ore body and have the potential to liberate methane based on the history of the mine or geological area in which the mine is located and in which—
(A) A concentration of 0.25 percent or more methane has not been detected in the mine atmosphere; and
(B) An ignition of methane has not occurred.
(iii) Subcategory I-C applies to mines in which the product extracted is combustible and the dust has a volatile matter content of 60 percent or more measured on a moisture free basis1
1 Measured by the American Society for Testing and Materials, ASTM D 3175–82, Standard Test Method for Volatile Matter in the Analysis Sample of Coal and Coke. (This document is available at any Metal and Nonmetal Mine Safety and Health District Office of the Mine Safety and Health Administration).
(2) Category II applies to domal salt mines where the history of the mine or geological area indicates the occurrence of or the potential for an outburst. Category II is divided into Subcategories II-A and II-B as follows:
(i) Subcategory II-A applies to domal salt mines where an outburst reportable under §57.22004(c)(1) has occurred.
(ii) Subcategory II-B applies to domal salt mines where an outburst reportable under §57.22004(c)(1) has not occurred, but which have the potential for an outburst based on the history of the mine or geological area in which the mine is located.
(3) Category III applies to mines in which noncombustible ore is extracted and which liberate a concentration of methane that is explosive, or is capable of forming explosive mixtures with air, or have the potential to do so based on the history of the mine or the geological area in which the mine is located. The concentration of methane in such mines is explosive or is capable of forming explosive mixtures if mixed with air as illustrated by Table 1 below, entitled “Relation Between Quantitative Composition and Explosibility of Mixtures of Methane and Air”.
View or download PDF
(4) Category IV applies to mines in which noncombustible ore is extracted and which liberate a concentration of methane that is not explosive nor capable of forming explosive mixtures with air based on the history of the mine or the geological area in which the mine is located. The concentration of methane in such mines is not explosive nor capable of forming explosive mixtures if mixed with air as illustrated by Table 1 above, entitled “Relation Between Quantitative Composition and Explosibility of Mixtures of Methane and Air”.
(5) Category V applies to petroleum mines. Category V is divided into Subcategories V-A and V-B as follows:
(i) Subcategory V-A applies to petroleum mines that operate entirely or partially within an oil reservoir; and all other petroleum mines in which—
(A) A concentration of 0.25 percent or more methane has been detected in the mine atmosphere and confirmed by laboratory analysis; or
(B) An ignition of methane has occurred.
(ii) Subcategory V-B applies to petroleum mines that operate outside of and drill into an oil resevoir and in which—
(A) A concentration of 0.25 percent or more methane has not been detected in the mine atmosphere; and
(B) An ignition of methane has not occurred.
(6) Category VI applies to mines in which the presence of methane has not been established and are not included in another category or subcategory.
(b) Category or subcategory placement or change in placement shall include consideration of the following:
(1) The history and geology of the mine or of the geological area in which the mine is located;
(2) The ore body and host rock;
(3) The character, amount, duration, origin, and nature of methane emission and the presence of explosive dust and inert gases; and
(4) Whether or not conditions encountered during primary or access development are transient or permanent.
(c)(1) Gas samples for the purpose of category or subcategory placement or change in placement, and for determining action levels, shall be taken in the mine atmosphere. Gas samples taken to determine the nature and extent of an occurrence under §57.22004 (c) and (d) may be taken at any location, including the source, point of entry and the mine atmosphere.
(2) Tests for methane shall be made with hand-held methanometers, methane monitors, atmospheric monitoring systems, devices used to provide laboratory analysis of samples, or with other equally effective sampling devices. However, only methane samples that have been confirmed by laboratory analysis shall be used for category or subcategory placement or change in placement.
(d) Each mine and mill shall be required to operate in accordance with the safety standards applicable to its particular category or subcategory.
§ 57.22004 Category placement or change in placement.
The Administrator for Metal and Nonmetal Mine Safety and Health (Administrator) shall be responsible for category and subcategory placement, change in placement, and notification of placement of mines.
(a) The Administrator's proposed notice of placement or change in placement shall be sent to the mine operator and the appropriate representative of miners and shall include—
(1) The category or subcategory;
(2) The reasons for placement or change in placement;
(3) The data considered;
(4) The applicable standards and a time schedule for the mine operator to achieve compliance;
(5) Whether or not conditions encountered during primary or access development are transient or permanent; and
(6) Notification of the right to appeal the Administrator's determination under §57.22005.
(b) The operator or the representative of the miners shall have the right to request of the Administrator reassignment of the mine to a more appropriate category or subcategory if, based on operating experience, the conditions set forth in §57.22003(b) indicate that the hazards of methane exist under circumstances more appropriately governed by a different category or subcategory. In response to such a request, the procedures set forth in paragraph (d) of this section shall apply. While the request for category or subcategory reassignment is pending, the mine shall continue to operate under the standards for the category or subcategory to which originally assigned.
(c) MSHA shall be notified as soon as possible if any of the following events occur:
(1) An outburst that results in 0.25 percent or more methane in the mine atmosphere;
(2) A blowout that results in 0.25 percent or more methane in the mine atmosphere;
(3) An ignition of methane; or
(4) Air sample results that indicate 0.25 percent or more methane in the mine atmosphere of a Subcategory I-B, I-C, II-B, V-B or Category VI mine.
(d) The Administrator shall promptly appoint an MSHA committee to investigate occurrences reported in accordance with paragraph (c) of this section or requests filed in accordance with paragraph (b) of this section. Upon completion of an investigation, the committee shall make a written report of the findings. These investigations may include an evaluation of the following:
(1) Source, nature, and extent of occurrences;
(2) Conditions under which the incident occurred;
(3) Samples and tests;
(4) Physical conditions at the time of the occurrence;
(5) Charts, logs, and records related to the occurrence;
(6) Whether the occurrence is isolated, continuous, or could recur;
(7) Conditions indicating that the hazards of methane no longer exist or exist under circumstances more appropriately governed by a different category or subcategory;
(8) The geology of the mine and the geological area in which the mine is located; and
(9) Statements by witnesses, company officials, employees, and other persons having knowledge of the mine or the occurrence. Representatives of the mine operator, the miners and the appropriate State agency may participate in the investigation.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987; 60 FR 33722, June 29, 1995]
§ 57.22005 Notice and appeal of placement or change in placement.
(a) The Administrator's determination of category or subcategory placement or change in placement shall become final upon the 30th day after it is served on the mine operator and representative of miners, unless a request for a hearing has been filed. Service of the Administrator's determination is complete upon mailing by registered or certified mail, return receipt requested.
(b) The mine operator or representative of miners may obtain review of the Administrator's determination by filing a request for a hearing with the Assistant Secretary of Labor for Mine Safety and Health, Mine Safety and Health Administration, 1100 Wilson Blvd., Room 2322, Arlington, Virginia 22209–3939 within 30 days of the Administrator's determination. Service of a request for hearing is completed upon mailing by registered or certified mail, return receipt requested. Requests for a hearing shall be in writing and contain the following information:
(1) Name, address, and mine identification number;
(2) A concise statement of the reason why the Administrator's determination is inappropriate; and
(3) A copy of the Administrator's determination.
(c) The mine operator shall post a copy of the Administrator's determination and the request for a hearing on the mine bulletin board, and shall maintain the posting until the placement becomes final.
(d) Promptly after receipt of the request for a hearing, the Assistant Secretary shall refer to the Chief Administrative Law Judge, United States Department of Labor, the following:
(1) The request for a hearing;
(2) The Administrator's determination; and
(3) All information upon which the Administrator's determination was based.
(e) The hearing shall be regulated and conducted by an Administrative Law Judge in accordance with 29 CFR part 18, entitled, “Rules of Practice and Procedure for Administrative Hearings Before the Office of Administrative Law Judges.” Once the Administrative Law Judge has made an initial decision and served each party, the decision shall be final on the 30th day after service, unless discretionary review is undertaken by the Assistant Secretary or an appeal is filed by the mine operator or representative of the miners under paragraph (f) of this section.
(f) Within 30 days after service of an initial decision of an Administrative Law Judge, the Assistant Secretary for Mine Safety and Health may undertake a discretionary review of the initial decision, or the mine operator, or representative of the miners may appeal the initial decision of the Administrative Law Judge to the Assistant Secretary.
(1) The Assistant Secretary shall give notice of discretionary review to the mine operator and representative of the miners. The mine operator or representative of the miners shall give notice of an appeal to the other party. The notice shall specify the suggested changes and refer to the specific findings of fact, conclusions of law, and terms of the initial decision to be reviewed or appealed. The Assistant Secretary shall fix a time for filing any objections to the suggested changes and supporting reasons.
(2) The Assistant Secretary shall promptly notify the Administrative Law Judge of a discretionary review or an appeal. The entire record of the proceedings shall be transmitted to the Assistant Secretary for review.
(3) The Assistant Secretary shall make the final decision based upon consideration of the record of the proceedings. The final decision may affirm, modify, or set aside in whole or in part, the findings and conclusions contained in the initial decision. A statement of reasons for the action taken shall be included in the final decision. The final decision shall be served upon the mine operator and representative of the miners.
(g) Unless a decision by the Administrator for Metal and Nonmetal Mine Safety and Health, or the initial decision of the Administrative Law Judge, is appealed within 30 days, it becomes final, and is not subject to judicial review for the purposes of 5 U.S.C. 704. Only a decision by the Assistant Secretary shall be considered final Agency action for purposes of judicial review. Any such appeal must be filed in the appropriate circuit of the United States Court of Appeal.
(h) While a final decision of category placement is pending the following procedures shall apply:
(1) Where a mine has been classified as gassy prior to the effective date of these standards, existing gassy mines standards 30 CFR 57.21001 through 57.21101 (1986 Edition) shall continue to be applicable until placement is final.
(2) Where a mine has not been classified as gassy prior to the effective date of these standards and it is placed in Categories I through V, the mine shall comply with Category VI standards (§§57.22231, 57.22232, 57.22236, and 57.22238) until placement is final.
(3) Where a mine has been classified in Categories I through V after the effective date of these standards and category reassignment is being considered, the mine shall comply with the standards applicable to the category to which presently assigned until category placement is final.
[52 FR 24941, July 1, 1987; 52 FR 27903, July 24, 1987, as amended at 67 FR 38385, June 4, 2002]
Fire Prevention and Control
Note: The Category or Subcategory applicability of each standard appears in the parentheses of each standard's title line].
§ 57.22101 Smoking (I-A, II-A, III, and V-A mines).
Persons shall not smoke or carry smoking materials, matches, or lighters underground. The operator shall institute a reasonable program to assure that persons entering the mine do not carry such items.
§ 57.22102 Smoking (I-C mines).
(a) Persons shall not smoke or carry smoking materials, matches, or lighters underground or within 50 feet of a mine opening. The operator shall institute a reasonable program to assure that persons entering the mine do not carry such items.
(b) Smoking is prohibited in surface milling facilities except in designated, dust-free smoking areas.
§ 57.22103 Open flames (I-A, II-A, III, and V-A mines).
Open flames shall not be permitted underground except for welding, cutting, and other maintenance operations, and for igniting underground retorts in a Subcategory I-A mine. When using open flames in other than fresh air, or in places where methane may enter the air current, tests for methane shall be conducted by a competent person before work is started and every 10 minutes until the job is completed. Continuous methane monitors with audible alarms may be used after the initital test has been conducted as an alternative to the ten-minute interval testing requirement. Open flames shall not be used in atmospheres containing 0.5 percent or more methane.
§ 57.22104 Open flames (I-C mines).
(a) Open flames, including cutting and welding, shall not be used underground.
(b) Welding and cutting shall not be done within 50 feet of a mine opening unless all persons are out of the mine and the mine opening is covered. The cover shall be a substantial material, such as metal or wood, topped with a layer of wetted material to prevent sparks and flames from entering the mine opening.
§ 57.22105 Smoking and open flames (IV mines).
Smoking or open flames shall not be permitted in a face or raise, or during release of gas from a borehole until tests have been conducted in accordance with §57.22226 and the methane level has been determined to be below 0.5 percent.
§ 57.22106 Dust containing volatile matter (I-C mines).
Dust containing volatile matter shall not be allowed to accumulate on the surfaces of enclosures, facilities, or equipment used in surface milling in amounts that, if suspended in air, would become an explosive mixture. An explosive mixture of dust containing volatile matter is 0.02 ounce or more per cubic foot of air.
Ventilation
§ 57.22201 Mechanical ventilation (I-A, I-B, I-C, II-A, II-B, III, IV, V-A, and V-B mines).
All mines shall be ventilated mechanically.
§ 57.22202 Main fans (I-A, I-B, I-C, II-A, III, V-A, and V-B mines).
(a) Main fans shall be—
(1) Installed on the surface in noncombustible housings provided with noncombustible air ducts;
(2) Except in Subcategory I-A mines, provided with an automatic signal device to give an alarm when the fan stops. The signal device shall be located so that it can be seen or heard by a person designated by the mine operator.
(b) Fan installations shall be—
(1) Offset so that the fan and its associated components are not in direct line with possible explosive forces;
(2) Equipped with explosion-doors, a weak-wall, or other equivalent devices located to relieve the pressure that would be created by an explosion underground. The area of the doors or weak-wall shall be at least equivalent to the average cross-sectional area of the airway.
(c) (1) All main fan-related electrical equipment and cables located within or exposed to the forward or reverse airstream shall be approved by MSHA under the appliable requirements of 30 CFR part 18;
(2) Drive belts and nonmetallic fan blades shall be constructed of static-conducting material; and
(3) Aluminum alloy fan blades shall not contain more than 0.5 percent magnesium. [Paragraph (c)(3) of this section does not apply to Subcategory I-C mines].
(d) When an internal combustion engine is used to power a main fan or as standby power, the engine shall be—
(1) Installed in a noncombustible housing;
(2) Protected from a possible fuel supply fire or explosion; and
(3) Located out of direct line with the forward and reverse airstream provided by the fan. Engine exhaust gases shall be vented to the atomsphere so that exhaust cannot contaminate mine intake air.
(e) For Subcategory I-A mines only: Main exhaust fans shall be equipped with methane monitors to give an alarm when methane in the return air reaches 0.5 percent. The alarm shall be located so that it can be seen or heard by a person designated by the mine operator.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987]
§ 57.22203 Main fan operation (I-C mines).
Main fans shall be operated continuously while ore production is in progress.
§ 57.22204 Main fan operation and inspection (I-A, II-A, III, and V-A mines).
Main fans shall be—
(a) Provided with a pressure-recording system; and
(b) Inspected daily while operating if persons are underground. Certification of inspections shall be made by signature and date. Certifications and pressure recordings shall be retained for at least one year and made available to an authorized representative of the Secretary.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987; 60 FR 33722, June 29, 1995]
§ 57.22205 Doors on main fans (I-A, II-A, III, and V-A mines).
In mines ventilated by multiple main fans, each main fan installation shall be equipped with noncombustible doors. Such doors shall automatically close to prevent air reversal through the fan. The doors shall be located so that they are not in direct line with explosive forces which could come out of the mine.
§ 57.22206 Main ventilation failure (I-A, II-A, III, and V-A mines).
(a) When there has been a main ventilation failure, such as stoppage of main fans or failure of other components of the main ventilation system, tests for methane shall be conducted in affected active workings until normal air flow has resumed.
(b) If a total failure of ventilation occurs while all persons are out of the mine and the failure lasts for more than 30 minutes, only competent persons shall be allowed underground to examine the mine or to make necessary ventilation changes. Other persons may reenter the mine after the main fans have been operational for at least 30 minutes, or after the mine atmosphere has been tested and contains less than 1.0 percent methane. Persons other than examiners shall not reenter a Subcategory II-A mine until the methane level is less than 0.5 percent.
§ 57.22207 Booster fans (I-A, II-A, III, and V-A mines).
(a) Booster fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18, and be—
(1) Provided with an automatic signal device located so that it can be seen or heard by a person designated by the mine operator to give an alarm when the fan stops or when methane reaches the following levels:
(i) 1.0 percent at the fan in Subcategory I-A, Category III, and Subcategory V-A mines; and
(ii) 0.5 percent at the fan in Subcategory II-A mines.
(2) Equipped with a device that automatically deenergizes power in affected workings should the fan stop; and
(3) Equipped with starting and stopping controls located at the fan and at another accessible remote location.
(b) Booster fan installations, except for booster fans installed in ducts, shall be—
(1) Provided with doors which open automatically when all fans in the installation stop; and
(2) Provided with an air lock when passage through the fan bulkhead is necessary.
§ 57.22208 Auxiliary fans (I-A, II-A, III, and V-A mines).
(a) Auxiliary fans, except fans used in shops and other areas which have been so designed that methane cannot enter the airway, shall be approved by MSHA under the applicable requirements of 30 CFR part 18, and be operated so that recirculation is minimized. Auxiliary fans shall not be used to ventilate work places during the interruption of normal mine ventilatioin.
(b) Tests for methane shall be made at auxiliary fans before they are started.
§ 57.22209 Auxiliary fans (I-C mines).
Electric auxiliary fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18. Tests for methane shall be made at electric auxiliary fans before they are started. Such fans shall not be operated when air passing over or through them contains 0.5 percent or more methane.
§ 57.22210 In-line filters (I-C mines).
Filters or separators shall be installed on air-lift fan systems to prevent explosive concentrations of dust from passing through the fan.
§ 57.22211 Air flow (I-A mines).
The average air velocity in the last open crosscut in pairs or sets of developing entries, or through other ventilation openings nearest the face, shall be at least 40 feet per minute. The velocity of air ventilating each face at a work place shall be at least 20 feet per minute.
§ 57.22212 Air flow (I-C, II-A, and V-A mines).
Air flow across each working face shall be sufficient to carry away any accumulation of methane, smoke, fumes, and dust.
§ 57.22213 Air flow (III mines).
The quantity of air coursed through the last open crosscut in pairs or sets of entries, or through other ventilation openings nearest the face, shall be at least 6,000 cubic feet per minute, or 9,000 cubic feet per minute in longwall and continuous miner sections. The quantity of air across each face at a work place shall be at least 2,000 cubic feet per minute.
§ 57.22214 Changes in ventilation (I-A, II-A, III, and V-A mines).
(a) Changes in ventilation which affect the main air current or any split thereof and which adversely affect the safety of persons in the mine shall be made only when the mine is idle.
(b) Only persons engaged in making such ventilation changes shall be permitted in the mine during changes.
(c) Power shall be deenergized in affected areas prior to making ventilation changes, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18. Power shall not be restored until the results of the change have been determined and a competent person has examined affected working places for methane.
§ 57.22215 Separation of intake and return air (I-A, II-A, III, and V-A mines).
Main intake and return air currents shall be coursed through separate mine openings and shall be separated throughout the mine, except—
(a) Where multiple shafts are used for ventilation and a single shaft contains a curtain wall or partition for separation of air currents. Such wall or partition shall be constructed of reinforced concrete or other noncombustible equivalent, and provided with pressure-relief devices.
(b) During development of openings to the surface—
(1) Ventilation tubing approved by MSHA in accordance with 30 CFR part 7 or previously issued a BC or VT acceptance number by the MSHA Approval and Certification Center may be used for separation of main air currents in the same opening. Flexible ventilation tubing shall not exceed 250 feet in length.
(2) Only development related to making a primary ventilation connection may be performed beyond 250 feet of the shaft.
[52 FR 24941, July 1, 1987, as amended at 54 FR 30508, July 20, 1989]
§ 57.22216 Separation of intake and return air (I-C mines).
The main intake and return air currents in single shafts shall be separated by ventilation tubing, curtain walls, or partitions. Ventilation tubing shall be constructed of noncombustible material. Curtain walls or partitions shall be constructed of reinforced concrete or other noncombustible equivalent, and provided with pressure-relief devices.
§ 57.22217 Seals and stoppings (I-A, I-B, and I-C mines).
All seals, and those stoppings that separate main intake from main return airways, shall be of substantial construction and constructed of noncombustible materials, except that stoppings constructed of brattice materials may be used in face areas.
§ 57.22218 Seals and stoppings (III, V-A, and V-B mines).
(a) All seals, and those stoppings that separate main intake from main return airways, shall be of substantial construction, except that stoppings constructed of brattice materials may be used in face areas.
(b) Exposed surfaces on the intake side of stoppings constructed of combustible materials or foam-type blocks shall be coated with at least one inch of construction plaster containing perlite and gypsum; at least one inch of expanded vermiculite, Portland cement and limestone; or other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least 12 inches thick need not be coated for fire resistance. All foam-type blocks used for stopping construction shall be solid.
(c) Exposed surfaces on the fresh air side of seals constructed of combustible materials shall be coated with at least one inch of construction plaster containing perlite and gypsum; at least one inch of expanded vermiculite, Portland cement and limestone; or other coatings with equivalent fire resistance. Foam-type blocks shall not be used for seals.
§ 57.22219 Seals and stoppings (II-A mines).
(a) Exposed surfaces on the intake side of stoppings constructed of combustible materials, except brattice, shall be coated with at least one inch of construction plaster containing perlite and gypsum; at least one inch of expanded vermiculite, Portland cement and limestone; or other coatings with equivalent fire resistance.
(b) Seals shall be of substantial construction. Exposed surfaces on the fresh air side of seals constructed of combustible materials shall be coated with at least one inch of construction plaster containing perlite and gypsum; at least one inch of expanded vermiculite, Portland cement and limestone; or other coatings with equivalent fire resistance. Foam-type blocks shall not be used for seals.
§ 57.22220 Air passing unsealed areas (I-A, II-A, III, and V-A mines).
Air that has passed by or through unsealed abandoned or unsealed inactive areas and contains 0.25 percent or more methane shall—
(a) Be coursed directly to a return airway;
(b) Be tested daily for methane by a competent person; and
(c) Not be used to ventilate work places.
§ 57.22221 Overcast and undercast construction (I-A, II-A, III, and V-A mines).
Overcasts and undercasts shall be—
(a) Of substantial construction;
(b)(1) Constructed of noncombustible materials; or
(2) Where constructed of combustible materials, the outside surfaces shall be coated with at least one inch of construction plaster containing perlite and gypsum; at least one inch of expanded vermiculite, Portland cement and limestone; or other coatings with equivalent fire resistance;
(c) Kept clear of obstructions.
§ 57.22222 Ventilation materials (I-A, I-B, I-C, II-A, III, V-A, and V-B mines).
Brattice cloth and ventilation tubing shall be approved by MSHA in accordance with 30 CFR part 7, or shall bear a BC or VT acceptance number issued by the MSHA Approval and Certification Center.
[54 FR 30508, July 20, 1989]
§ 57.22223 Crosscuts before abandonment (III mines).
A means of ventilating faces shall be provided before workings are abandoned in unsealed areas, unless crosscuts are provided within 30 feet of the face.
§ 57.22224 Auxiliary equipment stations (I-A and III mines).
Battery charging stations, compressor stations, pump stations, and transformer stations shall be installed in intake air at locations which are sufficiently ventilated to prevent the accumulation of methane.
§ 57.22225 Auxiliary equipment stations (I-C mines).
Battery charging stations, compressor stations, and electrical substations shall not be installed underground or within 50 feet of a mine opening.
§ 57.22226 Testing for methane (IV mines).
Tests for methane shall be conducted in the mine atmosphere by a competent person—
(a) At least once each shift prior to starting work in each face and raise; and
(b) Upon initial release of gas into the mine atmosphere from boreholes.
§ 57.22227 Approved testing devices (I-A, I-B, I-C, II-A, II-B, III, IV, V-A, and V-B mines).
(a) Methane monitoring devices and portable, battery-powered, self-contained devices used for measuring methane, other gases, and contaminants in mine air shall be approved by MSHA under the applicable requirements of 30 CFR parts 18, 21, 22, 23, 27, and 29. Such devices shall be maintained in accordance with manufacturers' instructions, or an equivalent maintenance and calibration procedure.
(b)(1) Flame safety lamps shall not be used to test for methane except as supplementary devices.
(2) Flame safety lamps shall not be used in Subcategory I-C mines.
(c)(1) If electrically powered, remote sensing devices are used, that portion of the instrument located in return air or other places where combustible gases may be present shall be approved by MSHA under the applicable requirements of 30 CFR parts 18, 22, 23, 27, and 29.
(2) If air samples are delivered to remote analytical devices through sampling tubes, such tubes shall be provided with in-line flame arrestors. Pumping equipment and analytical instruments shall be located in intake air.
§ 57.22228 Preshift examination (I-A, I-C, II-A, III, and V-A mines).
(a) Preshift examinations shall be conducted within three hours prior to the start of the shift for which the examination is being made.
(b) Prior to the beginning of a shift following an idle shift, a competent person shall test the mine atmosphere for methane at all work places before persons other than examiners enter the mine.
(c) When one shift immediately follows another, a competent person shall test the mine atmosphere at each active working face for methane before work is started on that shift.
(d) A competent person shall test the mine atmosphere at each face blasted before work is started.
(e) Except in Subcategory I-C or Category III mines, vehicles used for transportation when examining the mine shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36.
[52 FR, 24941, July 1, 1987, as amended at 53 FR 9615, Mar. 24, 1988]
§ 57.22229 Weekly testing (I-A, III, and V-A mines).
(a) The mine atmosphere shall be tested for methane and carbon monoxide at least once every seven days by a competent person or an atmospheric monitoring system, or a combination of the two. Such testing shall be done at the following locations:
(1) The return of each split where it enters the main return;
(2) Adjacent to retreat areas, if accessible;
(3) At least one seal of each sealed area, if accessible;
(4) Main returns;
(5) At least one entry of each intake and return;
(6) Idle workings; and
(7) Return air from unsealed abandoned workings.
(b) The volume of air (velocity in Subcategory I-A mines) shall be measured at least once every seven days by a competent person. Such measurement shall be done at the following locations:
(1) Entering main intakes;
(2) Leaving main returns;
(3) Entering each main split;
(4) Returning from each main split; and
(5) In the last open crosscuts or other ventilation openings nearest the active faces where the air enters the return.
(c) Where such examinations disclose hazardous conditions, affected persons shall be informed and corrective action shall be taken.
(d) Certification of examinations shall be made by signature and date. Certifications shall be retained for at least one year and made available to authorized representatives of the Secretary.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987]
§ 57.22230 Weekly testing (II-A mines).
(a) The mine atmosphere shall be tested for methane at least once every seven days by a competent person or an atmospheric monitoring system, or a combination of the two. Such testing shall be done at the following locations:
(1) Active mining faces and benches;
(2) Main returns;
(3) Returns from idle workings;
(4) Returns from abandoned workings; and
(5) Seals.
(b) Where such examinations disclose hazardous conditions, affected persons shall be informed and corrective action shall be taken.
(c) Certification of examinations shall be made by signature and date. Certifications shall be kept for at least one year and made available to authorized representatives of the Secretary.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987; 60 FR 33723, June 29, 1995]
§ 57.22231 Actions at 0.25 percent methane (I-B, II-B, V-B, and VI mines).
If methane reaches 0.25 percent in the mine atmosphere, changes shall be made to improve ventilation, and MSHA shall be notified immediately.
§ 57.22232 Actions at 0.5 percent methane (I-B, II-A, II-B, IV, V-B, and VI mines).
If methane reaches 0.5 percent in the mine atmosphere, ventilation changes shall be made to reduce the level of methane. Until methane is reduced to less than 0.5 percent, electrical power shall be deenergized in affected areas, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18. Diesel equipment shall be shut off or immediately removed from the area and no other work shall be permitted in affected areas.
[52 FR 24941, July 1, 1987; 52 FR 27903, July 24, 1987]
§ 57.22233 Actions at 0.5 percent methane (I-C mines).
If methane reaches 0.5 percent in the mine atmosphere, ventilation changes shall be made to reduce the level of methane. Until methane is reduced to less than 0.5 percent, no other work shall be permitted in affected areas.
[52 FR 24941, July 1, 1987; 52 FR 27903, July 24, 1987]
§ 57.22234 Actions at 1.0 percent methane (I-A, I-B, III, V-A, and V-B mines).
(a) If methane reaches 1.0 percent in the mine atmosphere, ventilation changes shall be made to reduce the methane. Until such changes are achieved—
(1) All persons other than competent persons necessary to make the ventilation changes shall be withdrawn from affected areas;
(2) Electrical power shall be deenergized in affected areas, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18; and
(3) Diesel equipment shall be shut off or immediately removed from the area.
(b) If methane reaches 1.0 percent at a main exhaust fan, electrical power underground shall be deenergized, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18, and all persons shall be withdrawn from the mine.
(c) If methane reaches 1.0 percent at a work place and there has been a failure of the main ventilation system, all persons shall be withdrawn from the mine.
[52 FR, 24941, July 1, 1987, as amended at 53 FR 9615, Mar. 24, 1988]
§ 57.22235 Actions at 1.0 percent methane (I-C, II-A, II-B, and IV mines).
(a) If methane reaches 1.0 percent in the mine atmoshpere, all persons other than competent persons necessary to make ventilation changes shall be withdrawn from affected areas until methane is reduced to less than 0.5 percent.
(b) If methane reaches 1.0 percent at a work place and there has been a failure of the main ventilation system, all persons shall be withdrawn from the mine.
§ 57.22236 Actions at 1.0 percent methane (VI mines).
If methane reaches 1.0 percent in the mine atmosphere, all persons other than competent persons necessary to make ventilation changes shall be withdrawn from affected areas until methane is reduced to less than 0.5 percent.
§ 57.22237 Actions at 2.0 to 2.5 percent methane in bleeder systems (I-A and III mines).
If methane reaches 2.0 percent in bleeder systems at the point where a bleeder split enters a main return split, mining shall not be permitted on ventilation splits affected by the bleeder system. If methane has not been reduced to less than 2.0 percent within 30 minutes, or if methane levels reach 2.5 percent, all persons other than competent persons necessary to take corrective action shall be withdrawn from affected areas.
§ 57.22238 Actions at 2.0 percent methane (I-B, II-B, V-B, and VI mines).
If methane reaches 2.0 percent in the mine atmosphere, all persons other than competent persons necessary to make ventilation changes shall be withdrawn from the mine until methane is reduced to less than 0.5 percent.
§ 57.22239 Actions at 2.0 percent methane (IV mines).
If methane reaches 2.0 percent in the mine atmosphere, all persons other than competent persons necessary to make ventilation changes shall be withdrawn from the mine until methane is reduced to less than 0.5 percent. MSHA shall be notified immediately.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987; 60 FR 33723, June 29, 1995]
§ 57.22240 Actions at 2.0 percent methane (V-A mines).
If methane reaches 2.0 percent in the mine atmosphere, all persons other than competent persons necessary to make ventilation changes shall be withdrawn from affected areas until methane is reduced to less than 1.0 percent.
[52 FR 24941, July 1, 1987; 52 FR 27903, July 24, 1987]
§ 57.22241 Advance face boreholes (I-C mines).
(a) Boreholes shall be drilled at least 25 feet in advance of a face whenever the work place is within—
(1) 50 feet of a surveyed abandoned mine or abandoned workings which cannot be inspected; or
(2) 200 feet of an unsurveyed abandoned mine or abandoned workings which cannot be inspected.
(b) Boreholes shall be drilled in such a manner to insure that the advancing face will not accidently break into an abandoned mine or abandoned working.
Equipment
§ 57.22301 Atmospheric monitoring systems (I-A, II-A, and V-A mines).
(a) An atmospheric monitoring system shall be installed to provide surface readings of methane concentrations in the mine atmosphere from underground locations. Components of the system shall be approved by MSHA under the applicable requirements of 30 CFR parts 18, 22, 23, and 27; or be determined by MSHA under 30 CFR part 18 to be intrinsically safe or explosion-proof.
(b) Atmospheric monitoring systems shall—
(1) Give warnings on the surface and underground when methane at any sensor reaches 0.5 percent or more, and when power to a sensor is interrupted. Warning devices shall be located so that they can be seen and heard by a person designated by the mine operator; and
(2) Automatically deenergize power in affected areas, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18, when methane at any sensor reaches—
(i) 1.0 percent in a Subcategory I-A or V-A mine; or
(ii) 0.5 percent while persons are underground and 1.0 percent during blasting in a Subcategory II-A mine. Timing devices are permitted to avoid nuisance tripping for periods not to exceed 30 seconds, except during blasting or the ventilation time following a blast in a Subcategory II-A mine.
(c) Atmospheric monitoring systems shall be checked with a known mixture of methane, and calibrated if necessary at least once every 30 days. Certification of calibration tests shall be made by signature and date. Certifications of tests shall be retained for at least one year and made available to authorized representatives of the Secretary.
§ 57.22302 Approved equipment (I-A and V-A mines).
Equipment used in or beyond the last open crosscut shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36. Equipment shall not be operated in atmospheres containing 1.0 percent or more methane.
§ 57.22303 Approved equipment (I-C mines).
Only electrical equipment that is approved by MSHA under the applicable requirements of 30 CFR parts 18 through 28 or approved under 30 CFR part 29 contained in the 30 CFR, parts 1–199, edition, revised as of July 1, 1999, shall be used underground, except for submersible sump pumps.
[64 FR 43283, Aug. 10, 1999]
§ 57.22304 Approved equipment (II-A mines).
(a) Cutting and drilling equipment used at a face or bench shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36.
(b) While cutting or drilling is in progress, equipment not approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36 shall remain at least 100 feet from the face or bench being mined.
(c) Tests for methane shall be conducted immediately before nonapproved equipment is taken to a face or bench after blasting.
(d) Mine power transformers and stationary equipment not approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36 shall be installed in fresh air or downwind from an atmospheric methane monitor sensor.
§ 57.22305 Approved equipment (III mines).
Equipment used in or beyond the last open crosscut and equipment used in areas where methane may enter the air current, such as pillar recovery workings, longwall faces and shortwall faces, shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36. Equipment shall not be operated in atmospheres containing 1.0 percent or more methane.
§ 57.22306 Methane monitors (I-A mines).
(a) Methane monitors shall be installed on continuous mining machines, longwall mining systems, and on loading and haulage equipment used in or beyond the last open crosscut.
(b) The monitors shall—
(1) Give warning at 1.0 percent methane;
(2) Automatically deenergize electrical equipment, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18, and prevent starting such equipment when methane levels reach 1.5 percent. Diesel equipment shall be shut off or immediately removed from the affected area; and
(3) Automatically deenergize electrical equipment when power to a sensor is interrupted. Diesel equipment shall not be operated if the monitor is inoperative.
(c) Sensing units of monitors shall be positioned at a location which provides for the most effective measurement of methane.
§ 57.22307 Methane monitors (II-A mines).
(a) Methane monitors shall be installed on continuous mining machines, longwall mining systems, bench and face drills, and undercutting machines used in or beyond the last open crosscut.
(b) The monitors shall—
(1) Give warning at 0.5 percent methane;
(2) Automatically deenergize electrical equipment, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18, and prevent starting such equipment when methane levels reach 1.0 percent; and
(3) Automatically deenergize the equipment when power to a sensor is interrupted.
(c) Sensing units of monitors shall be positioned at a location which provides for the most effective measurement of methane.
§ 57.22308 Methane monitors (III mines).
(a) Methane monitors shall be installed on continuous mining machines and longwall mining systems.
(b) The monitors shall—
(1) Give warning at 1.0 percent methane;
(2) Automatically deenergize electrical equipment, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18, and prevent starting such equipment when methane levels reach 1.5 percent; and
(3) Automatically deenergize the equipment when power to a sensor is interrupted.
(c) Sensing units of monitors shall be positioned at a location which provides for the most effective measurement of methane.
§ 57.22309 Methane monitors (V-A mines).
(a) Methane monitors shall be installed on continuous mining machines used in or beyond the last open crosscut.
(b) The monitors shall—
(1) Give warning at 1.0 percent methane.
(2) Automatically deenergize electrical equipment, except power to monitoring equipment determined by MSHA to be intrinsically safe under 30 CFR part 18, and prevent starting of such equipment when methane levels reach 1.5 percent; and
(3) Automatically deenergize the equipment when power to a sensor is interrupted.
(c) Sensing units of monitors shall be positioned at a location which provides for the most effective measurement of methane.
§ 57.22310 Electrical cables (I-C mines).
Electrical cables used to power submersible sump pumps shall be accepted or approved by MSHA as flame resistant, or be installed in continuous metal conduit or metal pipe. The ends of such conduit or pipe shall be sealed to prevent entry of explosive gas or dust.
[57 FR 61223, Dec. 23, 1992]
§ 57.22311 Electrical cables (II-A mines).
Only jacketed electrical cables accepted or approved by MSHA as flame resistant shall be used to supply power to distribution boxes and electrical equipment operating in face and bench areas.
[57 FR 61223, Dec. 23, 1992]
§ 57.22312 Distribution boxes (II-A and V-A mines).
Distribution boxes containing short circuit protection for trailing cables of approved equipment shall be approved by MSHA under 30 CFR part 18.
§ 57.22313 Explosion-protection systems (I-C mines).
Pressure-relief systems including vents, or explosion suppression systems, shall be provided on explosive dust handling and processing equipment and on facilities housing such equipment. Vents shall be installed so that forces are directed away from persons should an explosion occur. The ratio of vent size to internal size of the equipment or facility shall not be less than one square foot of vent for each 80 cubic feet of volume or space.
§ 57.22314 Flow-control devices (V-A and V-B mines).
Oil recovery drill holes that penetrate oil bearing formations shall have devices to control the release of liquid hydrocarbons and hazardous gases during the drilling process. Such devices may be recovered for reuse after the formation has been depressurized or the well or borehole has been capped or connected to a collection system.
§ 57.22315 Self-contained breathing apparatus (V-A mines).
Self-contained breathing apparatus of a duration to allow for escape from the mine and sufficient in number to equip all persons underground shall be strategically located throughout the mine. Such apparatus shall be approved by MSHA and NIOSH under 42 CFR part 84 and shall be maintained in accordance with manufacturers' specifications. This standard does not apply to double entry mining systems where crosscut intervals do not exceed 250 feet.
[52 FR, 24941, July 1, 1987, as amended at 60 FR 30401, June 8, 1995]
Underground Retorts
§ 57.22401 Underground retorts (I-A and I-B mines).
(a) Retorts shall be provided with—
(1) Two independent power sources for main mine ventilation fans and those fans directly ventilating retort bulkheads, and for retort blowers, and provisions for switching promptly from one power source to the other; and
(2) An alarm system for blower malfunctions and an evacuation plan to assure safety of personnel in the event of a failure.
(b) Prior to the ignition of underground retorts, a written ignition and operation plan shall be submitted to the MSHA District Manager for the area in which the mine is located. The mine operator shall comply with all provisions of the retort plan. The retort plan shall include—
(1) Acceptable levels of combustible gases and oxygen in retort off-gases during start-up and during burning; levels at which corrective action will be initiated; levels at which personnel will be removed from the retort areas, from the mine, and from endangered surface areas; and the conditions for reentering the mine;
(2) Specification and locations of off-gas monitoring procedures and equipment;
(3) Specifications for construction of retort bulkheads and seals, and their locations;
(4) Procedures for ignition of a retort and for reignition following a shutdown; and
(5) Details of area monitoring and alarm systems for hazardous gases and actions to be taken to assure safety of personnel.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987; 60 FR 33723, June 29, 1995]
Illumination
§ 57.22501 Personal electric lamps (I-A, I-B, I-C, II-A, II-B, III, IV, V-A, and V-B mines).
Electric lamps used for personal illumination shall be approved by MSHA under the requirements of 30 CFR parts 19 or 20, as applicable.
Explosives
§ 57.22601 Blasting from the surface (I-A mines).
(a) All development, production, and bench rounds shall be initiated from the surface after all persons are out of the mine. Persons shall not enter the mine until ventilating air has passed over the blast area and through at least one atmospheric monitoring sensor.
(b) After blasting, if the monitoring system indicates that methane in the mine is less than 1.0 percent, persons may enter the mine. All places blasted shall be tested for methane by a competent person before work is started.
(c) If the monitoring system indicates the presence of 1.0 percent or more methane, persons other than examiners shall not enter the mine until the mine has been examined by a competent person and the methane content has been reduced to less than 1.0 percent.
(d) Vehicles used for transportation when examining the mine shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36.
[52 FR, 24941, July 1, 1987, as amended at 53 FR 9615, Mar. 24, 1988]
Effective Date Note: At 53 FR 9615, Mar. 24, 1988, §57.22601 was stayed until further notice.
§ 57.22602 Blasting from the surface (I-C mines).
(a) All blasting shall be initiated from the surface after all persons are out of the mine and any connecting mines.
(b) Persons shall not enter the mine until a competent person has examined the blast sites and methane concentrations are less than 0.5 percent.
§ 57.22603 Blasting from the surface (II-A mines).
(a) All development, production, and bench rounds shall be initiated from the surface after all persons are out of the mine. Persons shall not enter the mine until the mine has been ventilated for at least 15 minutes and the ventilating air has passed over the blast area and through at least one atmospheric monitoring sensor.
(b) If the monitoring system indicates that methane in the mine is less than 0.5 percent, competent persons may enter the mine to test for methane in all blast areas.
(c) If the monitoring system indicates that methane in the mine is 0.5 percent or more, the mine shall be ventilated and persons shall not enter the mine until the monitoring system indicates that methane in the mine is less than 0.5 percent.
(d) If the monitoring system is inoperable or malfunctions, the mine shall be ventilated for at least 45 minutes and the mine power shall be deenergized before persons enter the mine. Only competent persons necessary to test for methane may enter the mine until the methane in the mine is less than 0.5 percent.
(e) Vehicles used for transportation when examining the mine shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36. Vehicles shall not be used to examine the mine if the monitoring system is inoperable or has malfunctioned.
§ 57.22604 Blasting from the surface (II-B mines).
All development, production, and bench rounds shall be initiated from the surface after all persons are out of the mine. Persons other than those designated by the mine operator to make methane tests shall not enter the mine until all blast areas have been tested for methane.
§ 57.22605 Blasting from the surface (V-A mines).
(a) All development and production blasting shall be initiated from the surface after all persons are out of the mine. Persons shall not enter the mine until ventilating air has passed over the blast area and through at least one atmospheric monitoring sensor.
(b) If the monitoring system indicates that methane in the mine is less than 1.0 percent, persons may enter the mine, and all places blasted shall be tested for methane by a competent person before work is started.
(c) If the monitoring system indicates the presence of 1.0 percent or more methane, persons other than examiners shall not enter the mine until the mine has been examined by a competent person and the methane level is less than 1.0 percent.
(d) Vehicles used for transportation when examining the mine shall be approved by MSHA under the applicable requirements of 30 CFR parts 18 through 36.
(e) This standard applies only to mines blasting within an oil reservoir.
§ 57.22606 Explosive materials and blasting units (III mines).
(a) Mine operators shall notify the appropriate MSHA District Manager of all nonapproved explosive materials and blasting units to be used prior to their use. Explosive materials used for blasting shall be approved by MSHA under 30 CFR part 15, or nonapproved explosive materials shall be evaluated and determined by the District Manager to be safe for blasting in a potentially gassy environment. The notice shall also include the millisecond-delay interval between successive shots and between the first and last shot in a round.
(b) Faces shall be examined for proper placement of holes, possible breakthrough, and water. Ammonium nitrate blasting agents shall not be loaded into wet holes.
(c) Multiple-shot blasts shall be initiated with detonators encased in copper-based alloy shells. Aluminum and aluminum alloy-cased detonators, nonelectric detonators, detonating cord, and safety fuses shall not be used. All detonators in a round shall be made by the same manufacturer.
(d) Nonapproved explosives shall be used only as primers with ammonium nitrate-fuel oil blasting agents. Such primers shall be placed at the back or bottom of the hole.
(e) Blast holes shall be stemmed with a noncombustible material in an amount to confine the explosive charge. Breakthrough holes shall be stemmed at both ends.
(f) Mudcaps or other nonapproved unconfined shots shall not be blasted.
(g)(1) Blasting units shall be approved by MSHA under 30 CFR part 25; or
(2) Blasting units used to fire more than 20 detonators shall provide at least 2 amperes through each detonator but not more than an average of 100 amperes through one ohm for 10 milliseconds, and provide the necessary current for at least the first 5 milliseconds with a cutoff not to exceed 10 milliseconds.
[52 FR, 24941, July 1, 1987, as amended at 52 FR 41397, Oct. 27, 1987]
§ 57.22607 Blasting on shift (III mines).
When blasting on shift, tests for methane shall be made in the mine atmosphere by a competent person before blasting. Blasting shall not be done when 1.0 percent or more methane is present.
§ 57.22608 Secondary blasting (I-A, II-A, and V-A mines).
Prior to secondary blasting, tests for methane shall be made in the mine atmosphere at blast sites by a competent person. Secondary blasting shall not be done when 0.5 percent or more methane is present.
Appendix I to Subpart T of Part 57—Standard Applicability by Category or Subcategory
Subcategory I-A
57.22103
57.22201
57.22202
57.22204
57.22205
57.22206
57.22207
57.22208
57.22211
57.22214
57.22215
57.22217
57.22220
57.22221
57.22222
57.22224
57.22227
57.22228
57.22229
57.22234
57.22237
57.22301
57.22302
57.22306
57.22401
57.22501
57.22601
57.22608
Subcategory I-B
57.22202
57.22217
57.22222
57.22227
57.22231
57.22232
57.22234
57.22238
57.22401
57.22501
Subcategory I-C
57.22104
57.22106
57.22201
57.22202
57.22203
57.22209
57.22210
57.22212
57.22216
57.22217
57.22222
57.22225
57.22227
57.22228
57.22233
57.22235
57.22241
57.22303
57.22310
57.22313
57.22501
57.22602
Subcategory II-A
57.22103
57.22201
57.22202
57.22204
57.22205
57.22206
57.22207
57.22208
57.22212
57.22214
57.22215
57.22219
57.22220
57.22221
57.22222
57.22227
57.22228
57.22230
57.22232
57.22235
57.22301
57.22304
57.22307
57.22311
57.22312
57.22501
57.22603
57.22608
Subcategory II-B
57.22227
57.22231
57.22232
57.22235
57.22238
57.22501
57.22604
Category III
57.22103
57.22201
57.22202
57.22204
57.22205
57.22206
57.22207
57.22208
57.22213
57.22214
57.22215
57.22218
57.22220
57.22221
57.22222
57.22223
57.22224
57.22227
57.22228
57.22229
57.22234
57.22237
57.22305
57.22308
57.22501
57.22606
57.22607
Category IV
57.22201
57.22226
57.22227
57.22232
57.22235
57.22239
57.22501
Subcategory V-A
57.22103
57.22201
57.22202
57.22204
57.22205
57.22206
57.22207
57.22208
57.22212
57.22214
57.22215
57.22218
57.22220
57.22221
57.22222
57.22227
57.22228
57.22229
57.22234
57.22240
57.22301
57.22302
57.22309
57.22312
57.22314
57.22315
57.22501
57.22605
57.22608
Subcategory V-B
57.22202
57.22218
57.22222
57.22227
57.22231
57.22232
57.22234
57.22238
57.22314
57.22501
Category VI
57.22232
57.22236
57.22238
