42 C.F.R. Table to Subpart J of Part 84
Title 42 - Public Health
Title 42: Public Health
PART 84—APPROVAL OF RESPIRATORY PROTECTIVE DEVICES
Subpart J—Supplied-Air Respirators
Table to Subpart J of Part 84
Table 8_Air-Supply-Line Requirements and Tests [42 CFR part 84, subpart J]---------------------------------------------------------------------------------------------------------------- Requirements for the air-supply lines of the indicated type of supplied-air respirators Specific requirements ---------------------------------------------------------------------------- Type A Type B Type C----------------------------------------------------------------------------------------------------------------Length of hose..................... Maximum of 91 m. (300 Maximum of 23 m. (75 Maximum of 91 m. (300 feet) feet), in multiples feet) in multiples of in multiples of 7.6 m. (25 of 7.6 m. (25 feet). 7.6 m. (25 feet). feet). It will be permissible for the applicant to supply hose of the approved type of shorter length than 7.6 m. (25 feet) provided it meets the requirements of the part.Air flow........................... None.................. None.................. The air-supply hose with air regulating valve or orifice shall permit a flow of not less than 115 liters (4 cubic feet) per minute to tight-fitting and 170 liters (6 cubic feet) per minute to loose- fitting respiratory-inlet coverings through the maximum length of hose for which approval is granted and at the minimum specified air-supply pressure. The maximum flow shall not exceed 425 liters (15 cubic feet) per minute at the maximum specified air-supply pressure with the minimum length of hose for which approval is granted.Air flow........................... ......do.............. ......do.............. The air-supply hose, detachable coupling, and demand valve of the demand class or pressure-demand valve of the pressure- demand class for Type C supplied-air respirators, demand and pressure-demand classes, shall be capable of delivering respirable air at a rate of not less than 115 liters (4 cubic feet) per minute to the respiratory-inlet covering at an inhalation resistance not exceeding 50 millimeters (2 inches) of water-column height measured in the respiratory-inlet covering with any combination of air-supply pressure and length of hose within the applicant's specified range of pressure and hose length. The air-flow rate and resistance to inhalation shall be measured while the demand or pressure-demand valve is actuated 20 times per minute by a source of intermittent suction. The maximum rate of flow to the respiratory-inlet covering shall not exceed 425 liters (15 cubic feet) per minute under the specified operating conditions.Air-regulating valve............... ......do.............. ......do.............. If an air-regulating valve is provided, it shall be so designed that it will remain at a specific adjustment, which will not be affected by the ordinary movement of the wearer. The valve must be so constructed that the air supply with the maximum length of hose and at the minimum specified air-supply pressure will not be less than 115 liters (4 cubic feet) of air per minute to tight- fitting and 170 liters (6 cubic feet) of air per minute of loose-fitting respiratory inlet coverings for any adjustment of the valve. If a demand or pressure- demand valve replaces the air-regulating valve, it shall be connected to the air-supply at the maximum air pressure for which approval is sought by means of the minimum length of air-supply hose for which approval is sought. The outlet of the demand or pressure-demand valve shall be connected to a source of intermittent suction so that the demand or pressure-demand valve is actuated approximately 20 times per minute for a total of 100,000 inhalations. To expedite this test, the rate of actuation may be increased if mutually agreeable to the applicant and NIOSH. During this test the valve shall function without failure and without excessive wear of the moving parts. The demand or pressure-demand valve shall not be damaged in any way when subjected at the outlet to a pressure or suction of 25 cm. (10 inches) of water gage for 2 minutes.Noncollapsibility.................. The hose shall not Same as Type A........ None. collapse or exhibit permanent deformation when a force of 90 kg. (200 pounds) is applied for 5 minutes between 2 planes 7.6 cm. (3 inches) wide on opposite sides of the hose.Nonkinkability..................... None.................. None.................. A 7.6 m. (25 foot) section of the hose will be placed on a horizontal-plane surface and shaped into a one-loop coil with one end of the hose connected to an airflow meter and the other end of the hose supplied with air at the minimum specified supply pressure. The connection shall be in the plane of the loop. The other end of the hose will be pulled tangentially to the loop and in the plane of the loop until the hose straightens. To meet the requirements of this test the loop shall maintain a uniform near-circular shape and ultimately unfold as a spiral, without any localized deformation that decreases the flow of air to less than 90 percent of the flow when the hose is tested while remaining in a straight line.Strength of hose and couplings..... Hose and couplings Same as Type A........ Hose and couplings shall shall not separate or not exhibit any separation fail when tested with or failure when tested a pull of 113 kg. with a pull of 45 kg. (100 (250 pounds) for 5 pounds) for 5 minutes and minutes. when tested by subjecting them to an internal air pressure of 2 times the maximum respirator-supply pressure that is specified by the applicant or at 173 kN/m. 2 (25 pounds per square inch) gage, whichever is higher.Tightness.......................... No air leakage shall None.................. Leakage of air exceeding 50 occur when the hose cc. per minute at each and couplings are coupling shall not be joined and the permitted when the hose joint(s) are immersed and couplings are joined in water and and are immersed in water, subjected to an with air flowing through internal air pressure the respirator under a of 35 kN/m. 2 (5 pressure of 173 kN/m. 2 pounds per square (25 pounds per square inch) gage. inch) gage applied to the inlet end of the air- supply hose, or at twice the maximum respirator- supply pressure that is specified by the applicant, whichever is higher.Permeation of hose by gasoline..... The permeation of the Same as for Type A.... Same as for Type A, except hose by gasoline will the test period shall be 1 be tested by hour. immersing 7.6 m. (25 feet) of hose and one coupling in gasoline, with air flowing through the hose at the rate of 8 liters per minute for 6 hours. The air from the hose shall not contain more than 0.01 percent by volume of gasoline vapor at the end of the test.Detachable coupling................ None.................. None.................. A hand-operated detachable coupling by which the wearer can readily attach or detach the connecting hose shall be provided at a convenient location. This coupling shall be durable, remain connected under all conditions of normal respirator use, and meet the prescribed tests for strength and tightness of hose and couplings.----------------------------------------------------------------------------------------------------------------
