49 C.F.R. Subpart A—General
Title 49 - Transportation
(a) This part prescribes Federal safety standards for freight and other non-passenger train brake systems and equipment. Subpart E of this part prescribes Federal safety standards not only for freight and other non-passenger train brake systems and equipment, but also for passenger train brake systems. This part does not restrict a railroad from adopting or enforcing additional or more stringent requirements not inconsistent with this part. (b) Except as otherwise specifically provided in this paragraph or in this part, railroads to which this part applies shall comply with all the requirements contained in subparts A through C and subpart F of this part beginning on April 1, 2004. Sections 232.1 through 232.13 and 232.17 through 232.21 of this part will become applicable to all railroads to which this part applies beginning on May 31, 2001. Subpart D of this part will become applicable to all railroads to which this part applies beginning on August 1, 2001. Subpart E of this part will become applicable to all trains operating on track which is part of the general railroad system of transportation beginning on May 31, 2001. (c) A railroad may request earlier application of the requirements contained in subparts A through C and subpart F of this part upon written notification to FRA's Associate Administrator for Safety. Such a request shall indicate the railroad's readiness and ability to comply with all of the requirements contained in those subparts. (d) Except for operations identified in §232.3(c)(1), (c)(4), and (c)(6) through (c)(8), all railroads which are part of the general railroad system of transportation shall operate pursuant to the requirements contained in this part 232 as it existed on May 31, 2001 and included as Appendix B to this part until they are either required to operate pursuant to the requirements contained in this part or the requirements contained in part 238 of this chapter or they elect to comply earlier than otherwise required with the requirements contained in this part or the requirements contained in part 238 of this chapter. [66 FR 4193, Jan. 17, 2001, as amended at 66 FR 9906, Feb. 12, 2001] (a) Except as provided in paragraphs (b) and (c) of this section, this part applies to all railroads that operate freight or other non-passenger train service on standard gage track which is part of the general railroad system of transportation. This includes the operation of circus trains and private cars when hauled on such railroads. (b) Subpart E of this part, “End-of-Train Devices,” applies to all trains operating on track which is part of the general railroad system of transportation unless specifically excepted in that subpart. (c) Except as provided in §232.1(d) and paragraph (b) of this section, this part does not apply to: (1) A railroad that operates only on track inside an installation that is not part of the general railroad system of transportation. (2) Intercity or commuter passenger train operations on standard gage track which is part of the general railroad system of transportation; (3) Commuter or other short-haul rail passenger train operations in a metropolitan or suburban area (as described by 49 U.S.C. 20102(1)), including public authorities operating passenger train service; (4) Rapid transit operations in an urban area that are not connected with the general railroad system of transportation; (5) Tourist, scenic, historic, or excursion operations, whether on or off the general railroad system; (6) Freight and other non-passenger trains of four-wheel coal cars; (7) Freight and other non-passenger trains of eight-wheel standard logging cars if the height of each car from the top of the rail to the center of the coupling is not more than 25 inches; or (8) A locomotive used in hauling a train referred to in paragraph (c)(7) of this subsection when the locomotive and cars of the train are used only to transport logs. (d) The provisions formerly contained in Interstate Commerce Commission Order 13528, of May 30, 1945, as amended, now revoked, are codified in this paragraph. This part is not applicable to the following equipment: (1) Scale test weight cars. (2) Locomotive cranes, steam shovels, pile drivers, and machines of similar construction, and maintenance machines built prior to September 21, 1945. (3) Export, industrial, and other cars not owned by a railroad which are not to be used in service, except for movement as shipments on their own wheels to given destinations. Such cars shall be properly identified by a card attached to each side of the car, signed by the shipper, stating that such movement is being made under the authority of this paragraph. (4) Industrial and other than railroad-owned cars which are not to be used in service except for movement within the limits of a single switching district (i.e., within the limits of an industrial facility). (5) Narrow-gage cars. (6) Cars used exclusively in switching operations and not used in train movements within the meaning of the Federal safety appliance laws (49 U.S.C. 20301–20306). The definitions in this section are intended to clarify the meaning of terms used in this part as it becomes applicable pursuant to §232.1(b) and (c). AAR means the Association of American Railroads. Air brake means a combination of devices operated by compressed air, arranged in a system, and controlled manually, electrically, electronically, or pneumatically, by means of which the motion of a railroad car or locomotive is retarded or arrested. Air Flow Indicator, AFM means a specific air flow indicator required by the air flow method of qualifying train air brakes (AFM). The AFM Air Flow Indicator is a calibrated air flow measuring device which is clearly visible and legible in daylight and darkness from the engineer's normal operating position. The indicator face displays: (1) Markings from 10 cubic feet per minute (CFM) to 80 CFM, in increments of 10 CFM or less; and (2) Numerals indicating 20, 40, 60, and 80 CFM for continuous monitoring of air flow. Bind means restrict the intended movement of one or more brake system components by reduced clearance, by obstruction, or by increased friction. Brake, dynamic means a train braking system whereby the kinetic energy of a moving train is used to generate electric current at the locomotive traction motors, which is then dissipated through resistor grids or into the catenary or third rail system. Brake, effective means a brake that is capable of producing its nominally designed retarding force on the train. A car's air brake is not considered effective if it is not capable of producing its nominally designed retarding force or if its piston travel exceeds: (1) 10 (2) The piston travel limit indicated on the stencil, sticker, or badge plate for that brake cylinder. Brake, hand means a brake that can be applied and released by hand to prevent or retard the movement of a locomotive. Brake indicator means a device which indicates the brake application range and indicates whether brakes are applied and released. Brake, inoperative means a primary brake that, for any reason, no longer applies or releases as intended. Brake, inoperative dynamic means a dynamic brake that, for any reason, no longer provides its designed retarding force on the train. Brake, parking means a brake that can be applied by means other than by hand, such as spring, hydraulic, or air pressure when the brake pipe air is depleted, or by an electrical motor. Brake pipe means the system of piping (including branch pipes, angle cocks, cutout cocks, dirt collectors, hoses, and hose couplings) used for connecting locomotives and all railroad cars for the passage of compressed air. Brake, primary means those components of the train brake system necessary to stop the train within the signal spacing distance without thermal damage to friction braking surfaces. Brake, secondary means those components of the train brake system which develop supplemental brake retarding force that is not needed to stop the train within signal spacing distances or to prevent thermal damage to wheels. Emergency application means an irretrievable brake application resulting in the maximum retarding force available from the train brake system. End-of-train device, one-way means two pieces of equipment linked by radio that meet the requirements of §232.403. End-of-train device, two-way means two pieces of equipment linked by radio that meet the requirements of §§232.403 and 232.405. Foul means any condition which restricts the intended movement of one or more brake system components because the component is snagged, entangled, or twisted. Freight car means a vehicle designed to carry freight, or railroad personnel, by rail and a vehicle designed for use in a work or wreck train or other non-passenger train. Initial terminal means the location where a train is originally assembled. Locomotive means a piece of railroad on-track equipment, other than hi-rail, specialized maintenance, or other similar equipment, which may consist of one or more units operated from a single control stand— (1) With one or more propelling motors designed for moving other railroad equipment; (2) With one or more propelling motors designed to transport freight or passenger traffic or both; or (3) Without propelling motors but with one or more control stands. Locomotive cab means that portion of the superstructure designed to be occupied by the crew operating the locomotive. Locomotive, controlling means the locomotive from which the engineer exercises control over the train. Off air means not connected to a continuous source of compressed air of at least 60 pounds per square inch (psi). Ordered date or date ordered means the date on which notice to proceed is given by a procuring railroad to a contractor or supplier for new equipment. Piston travel means the amount of linear movement of the air brake hollow rod (or equivalent) or piston rod when forced outward by movement of the piston in the brake cylinder or actuator and limited by the brake shoes being forced against the wheel or disc. Pre-revenue service acceptance testing plan means a document, as further specified in §232.505, prepared by a railroad that explains in detail how pre-revenue service tests of certain equipment demonstrate that the equipment meets Federal safety standards and the railroad's own safety design requirements. Previously tested equipment means equipment that has received a Class I brake test pursuant to §232.205 and has not been off air for more than four hours. Primary responsibility means the task that a person performs at least 50 percent of the time. The totality of the circumstances will be considered on a case-by-case basis in circumstances where an individual does not spend 50 percent of the day engaged in any one readily identifiable type of activity. Qualified mechanical inspector means a qualified person who has received, as a part of the training, qualification, and designation program required under §232.203, instruction and training that includes “hands-on” experience (under appropriate supervision or apprenticeship) in one or more of the following functions: troubleshooting, inspection, testing, maintenance or repair of the specific train brake components and systems for which the person is assigned responsibility. This person shall also possess a current understanding of what is required to properly repair and maintain the safety-critical brake components for which the person is assigned responsibility. Further, the qualified mechanical inspector shall be a person whose primary responsibility includes work generally consistent with the functions listed in this definition. Qualified person means a person who has received, as a part of the training, qualification, and designation program required under §232.203, instruction and training necessary to perform one or more functions required under this part. The railroad is responsible for determining that the person has the knowledge and skills necessary to perform the required function for which the person is assigned responsibility. The railroad determines the qualifications and competencies for employees designated to perform various functions in the manner set forth in this part. Although the rule uses the term “qualified person” to describe a person responsible for performing various functions required under this part, a person may be deemed qualified to perform some functions but not qualified to perform other functions. For example, although a person may be deemed qualified to perform the Class II/intermediate brake test required by this part, that same person may or may not be deemed qualified to perform the Class I/initial Terminal brake test or authorize the movement of defective equipment under this part. The railroad will determine the required functions for which an individual will be deemed a “qualified person” based upon the instruction and training the individual has received pursuant to §232.203 concerning a particular function. Railroad means any form of non-highway ground transportation that runs on rails or electromagnetic guideways, including: (1) Commuter or short-haul railroad passenger service in a metropolitan or suburban area and commuter railroad service that was operated by the Consolidated Rail Corporation on January 1, 1979; and (2) High speed ground transportation systems that connect metropolitan areas, without regard to whether those systems use new technologies not associated with traditional railroads. The term “railroad” is also intended to mean a person that provides transportation by railroad, whether directly or by contracting out operation of the railroad to another person. The term does not include rapid transit operations in an urban area that are not connected to the general railroad system of transportation. Rebuilt equipment means equipment that has undergone overhaul identified by the railroad as a capital expense under the Surface Transportation Board's accounting standards. Refresher training means periodic retraining required for employees or contractors to remain qualified to perform specific equipment troubleshooting, inspection, testing, maintenance, or repair functions. Respond as intended means to produce the result that a device or system is designed to produce. “Roll-by” inspection means an inspection performed while equipment is moving. Service application means a brake application that results from one or more service reductions or the equivalent. Service reduction means a decrease in brake pipe pressure, usually from 5 to 25 psi at a rate sufficiently rapid to move the operating valve to service position, but at a rate not rapid enough to move the operating valve to emergency position. Solid block of cars means two or more freight cars coupled together and added to or removed from a train as a single unit. State inspector means an inspector of a participating State rail safety program under part 212 of this chapter. Switching service means the classification of freight cars according to commodity or destination; assembling of cars for train movements; changing the position of cars for purposes of loading, unloading, or weighing; placing of locomotives and cars for repair or storage; or moving of rail equipment in connection with work service that does not constitute a train movement. Tourist, scenic, historic, or excursion operations are railroad operations that carry passengers, often using antiquated equipment, with the conveyance of the passengers to a particular destination not being the principal purpose. Train means one or more locomotives coupled with one or more freight cars, except during switching service. Train line means the brake pipe or any non-pneumatic system used to transmit the signal that controls the locomotive and freight car brakes. Train, unit or train, cycle means a train that, except for the changing of locomotive power and the removal or replacement of defective equipment, remains coupled as a consist and continuously operates from location A to location B and back to location A. Transfer train means a train that travels between a point of origin and a point of final destination not exceeding 20 miles. Such trains may pick up or deliver freight equipment while en route to destination. Yard air means a source of compressed air other than from a locomotive. [66 FR 4193, Jan. 17, 2001, as amended at 67 FR 17580, Apr. 10, 2002] (a) Any person subject to a requirement of this part may petition the Administrator for a waiver of compliance with such requirement. The filing of such a petition does not affect that person's responsibility for compliance with that requirement while the petition is being considered. (b) Each petition for waiver must be filed in the manner and contain the information required by part 211 of this chapter. (c) If the Administrator finds that a waiver of compliance is in the public interest and is consistent with railroad safety, the Administrator may grant the waiver subject to any conditions the Administrator deems necessary. If a waiver is granted, the Administrator publishes a notice in the (a) A railroad subject to this part shall not use, haul, permit to be used or hauled on its line, offer in interchange, or accept in interchange any train, railroad car, or locomotive with one or more conditions not in compliance with this part; however, a railroad shall not be liable for a civil penalty for such action if such action is in accordance with §232.15. For purposes of this part, a train, railroad car, or locomotive will be considered in use prior to departure but after it has received, or should have received, the inspection required for movement and is deemed ready for service. (b) Although many of the requirements of this part are stated in terms of the duties of a railroad, when any person performs any function required by this part, that person (whether or not a railroad) is required to perform that function in accordance with this part. (c) Any person performing any function or task required by this part shall be deemed to have consented to FRA inspection of the person's operation to the extent necessary to determine whether the function or task is being performed in accordance with the requirements of this part. (a) Any person (including but not limited to a railroad; any manager, supervisor, official, or other employee or agent of a railroad; any owner, manufacturer, lessor, or lessee of railroad equipment, track, or facilities; any employee of such owner, manufacturer, lessor, lessee, or independent contractor) who violates any requirement of this part or causes the violation of any such requirement is subject to a civil penalty of at least $550, but not more than $11,000 per violation, except that: Penalties may be assessed against individuals only for willful violations, and, where a grossly negligent violation or a pattern of repeated violations has created an imminent hazard of death or injury to persons, or has caused death or injury, a penalty not to exceed $27,000 per violation may be assessed. Each day a violation continues shall constitute a separate offense. Appendix A to this part contains a schedule of civil penalty amounts used in connection with this rule. (b) Any person who knowingly and willfully falsifies a record or report required by this part is subject to criminal penalties under 49 U.S.C. 21311. [66 FR 4193, Jan. 17, 2001, as amended at 69 FR 30594, May 28, 2004] (a) Under 49 U.S.C. 20106, issuance of the regulations in this part preempts any State law, rule, regulation, order, or standard covering the same subject matter, except for a provision necessary to eliminate or reduce a local safety hazard if that provision is not incompatible with this part and does not impose an undue burden on interstate commerce. (b) Preemption should also be considered pursuant to the Locomotive Boiler Inspection Act (now codified at 49 U.S.C. 20701–20703), the Safety Appliance Acts (now codified at 49 U.S.C. 20301–20304), and the Commerce Clause based on the relevant case law pertaining to preemption under those provisions. (c) FRA does not intend by issuance of the regulations in this part to preempt provisions of State criminal law that impose sanctions for reckless conduct that leads to actual loss of life, injury, or damage to property, whether such provisions apply specifically to railroad employees or generally to the public at large. (a) General provision. Except as provided in paragraph (c) of this section, a railroad car or locomotive with one or more conditions not in compliance with this part may be used or hauled without civil penalty liability under this part only if all of the following conditions are met: (1) The defective car or locomotive is properly equipped in accordance with the applicable provisions of 49 U.S.C. chapter 203 and the requirements of this part. (2) The car or locomotive becomes defective while it is being used by the railroad on its line or becomes defective on the line of a connecting railroad and is properly accepted in interchange for repairs in accordance with paragraph (a)(7) of this section. (3) The railroad first discovers the defective condition of the car or locomotive prior to moving it for repairs. (4) The movement of the defective car or locomotive for repairs is from the location where the car or locomotive is first discovered defective by the railroad. (5) The defective car or locomotive cannot be repaired at the location where the railroad first discovers it to be defective. (6) The movement of the car or locomotive is necessary to make repairs to the defective condition. (7) The location to which the car or locomotive is being taken for repair is the nearest available location where necessary repairs can be performed on the line of the railroad where the car or locomotive was first found to be defective or is the nearest available location where necessary repairs can be performed on the line of a connecting railroad if: (i) The connecting railroad elects to accept the defective car or locomotive for such repair; and (ii) The nearest available location where necessary repairs can be performed on the line of the connecting railroad is no farther than the nearest available location where necessary repairs can be performed on the line of the railroad where the car or locomotive was found defective. (8) The movement of the defective car or locomotive for repairs is not by a train required to receive a Class I brake test at that location pursuant to §232.205. (9) The movement of the defective car or locomotive for repairs is not in a train in which less than 85 percent of the cars have operative and effective brakes. (10) The defective car or locomotive is tagged, or information is recorded, as prescribed in paragraph (b) of this section. (11) Except for cars or locomotives with brakes cut out en route, the following additional requirements are met: (i) A qualified person shall determine— (A) That it is safe to move the car or locomotive; and (B) The maximum safe speed and other restrictions necessary for safely conducting the movement. (ii) The person in charge of the train in which the car or locomotive is to be moved shall be notified in writing and inform all other crew members of the presence of the defective car or locomotive and the maximum speed and other restrictions determined under paragraph (a)(11)(i)(B) of this section. A copy of the tag or card described in paragraph (b) of this section may be used to provide the notification required by this paragraph. (iii) The defective car or locomotive is moved in compliance with the maximum speed and other restrictions determined under paragraph (a)(11)(i)(B) of this section. (12) The defective car or locomotive is not subject to a Special Notice for Repair under part 216 of this chapter, unless the movement of the defective car is made in accordance with the restrictions contained in the Special Notice. (b) Tagging of defective equipment. (1) At the place where the railroad first discovers the defect, a tag or card shall be placed on both sides of the defective equipment, except that defective locomotives may have the tag or card placed in the cab of the locomotive. In lieu of a tag or card, an automated tracking system approved for use by FRA shall be provided. The tag, card, or automated tracking system shall contain the following information about the defective equipment: (i) The reporting mark and car or locomotive number; (ii) The name of the inspecting railroad; (iii) The name and job title of the inspector; (iv) The inspection location and date; (v) The nature of each defect; (vi) A description of any movement restrictions; (vii) The destination where the equipment will be repaired; and (viii) The signature, or electronic identification, of the person reporting the defective condition. (2) The tag or card required by paragraph (b)(1) of this section shall remain affixed to the defective equipment until the necessary repairs have been performed. (3) An electronic or written record or a copy of each tag or card attached to or removed from a car or locomotive shall be retained for 90 days and, upon request, shall be made available within 15 calendar days for inspection by FRA or State inspectors. (4) Each tag or card removed from a car or locomotive shall contain the date, location, reason for its removal, and the signature of the person who removed it from the piece of equipment. (5) Any automated tracking system approved by FRA to meet the tagging requirements contained in paragraph (b)(1) of this section shall be capable of being reviewed and monitored by FRA at any time to ensure the integrity of the system. FRA's Associate Administrator for Safety may prohibit or revoke a railroad's authority to utilize an approved automated tracking system in lieu of tagging if FRA finds that the automated tracking system is not properly secure, is inaccessible to FRA or a railroad's employees, or fails to adequately track and monitor the movement of defective equipment. FRA will record such a determination in writing, include a statement of the basis for such action, and provide a copy of the document to the railroad. (c) Movement for unloading or purging of defective cars. If a defective car is loaded with a hazardous material or contains residue of a hazardous material, the car may not be placed for unloading or purging unless unloading or purging is consistent with determinations made and restrictions imposed under paragraph (a)(11)(i) of this section and the unloading or purging is necessary for the safe repair of the car. (d) Computation of percent operative power brakes. (1) The percentage of operative power brakes in a train shall be based on the number of control valves in the train. The percentage shall be determined by dividing the number of control valves that are cut-in by the total number of control valves in the train. A control valve shall not be considered cut-in if the brakes controlled by that valve are inoperative. Both cars and locomotives shall be considered when making this calculation. (2) The following brake conditions not in compliance with this part are not considered inoperative power brakes for purposes of this section: (i) Failure or cutting out of secondary brake systems; (ii) Inoperative or otherwise defective handbrakes or parking brakes; (iii) Piston travel that is in excess of the Class I brake test limits required in §232.205 but that does not exceed the outside limits contained on the stencil, sticker, or badge plate required by §232.103(g) for considering the power brakes to be effective; and (iv) Power brakes overdue for inspection, testing, maintenance, or stenciling under this part. (e) Placement of equipment with inoperative brakes. (1) A freight car or locomotive with inoperative brakes shall not be placed as the rear car of the train. (2) No more than two freight cars with either inoperative brakes or not equipped with power brakes shall be consecutively placed in the same train. (3) Multi-unit articulated equipment shall not be placed in a train if the equipment has more than two consecutive individual control valves cut-out or if the brakes controlled by the valves are inoperative. (f) Guidelines for determining locations where necessary repairs can be performed. The following guidelines will be considered by FRA when determining whether a location is a location where repairs to a car's brake system or components can be performed and whether a location is the nearest location where the needed repairs can be effectuated. (1) The following general factors and guidelines will be considered when making determinations as to whether a location is a location where brake repairs can be performed: (i) The accessibility of the location to persons responsible for making repairs; (ii) The presence of hazardous conditions that affect the ability to safely make repairs of the type needed at the location; (iii) The nature of the repair necessary to bring the car into compliance; (iv) The need for railroads to have in place an effective means to ensure the safe and timely repair of equipment; (v) The relevant weather conditions at the location that affect accessibility or create hazardous conditions; (vi) A location need not have the ability to effectuate every type of brake system repair in order to be considered a location where some brake repairs can be performed; (vii) A location need not be staffed continuously in order to be considered a location where brake repairs can be performed; (viii) The ability of a railroad to perform repair track brake tests or single car tests at a location shall not be considered; and (ix) The congestion of work at a location shall not be considered (2) The general factors and guidelines outlined in paragraph (f)(1) of this section should be applied to the following locations: (i) A location where a mobile repair truck is used on a regular basis; (ii) A location where a mobile repair truck originates or is permanently stationed; (iii) A location at which a railroad performs mechanical repairs other than brake system repairs; and (iv) A location that has an operative repair track or repair shop; (3) In determining whether a location is the nearest location where the necessary brake repairs can be made, the distance to the location is a key factor but should not be considered the determining factor. The distance to a location must be considered in conjunction with the factors and guidance outlined in paragraphs (f)(1) and (f)(2) of this section. In addition, the following safety factors must be considered in order to optimize safety: (i) The safety of the employees responsible for getting the equipment to or from a particular location; and (ii) The potential safety hazards involved with moving the equipment in the direction of travel necessary to get the equipment to a particular location. (g) Designation of repair locations. Based on the guidance detailed in paragraph (f) of this section and consistent with other requirements contained in this part, a railroad may submit a detailed petition, pursuant to the special approval procedures contained in §232.17, containing a plan designating locations where brake system repairs will be performed. Approval of such plans shall be made accordance with the procedures contained in §232.17, and shall be subject to any modifications determined by FRA to be necessary to ensure consistency with the requirements and guidance contained in this part. [66 FR 4193, Jan. 17, 2001, as amended at 67 FR 17580, Apr. 10, 2002] (a) General. The following procedures govern consideration and action upon requests for special approval of a plan under §232.15(g), an alternative standard under §232.305, and for special approval of pre-revenue service acceptance testing plans under subpart F of this part. (b) Petitions for special approval of a plan or an alternative standard. Each petition for special approval of a plan under §232.15(g) or an alternative standard shall contain: (1) The name, title, address, and telephone number of the primary person to be contacted with regard to review of the petition; (2) The proposed plan pursuant to §232.15(g) or the proposed alternative standard, in detail, to be substituted for the particular requirement of this part; (3) Appropriate data or analysis, or both, for FRA to consider in determining whether the plan is consistent with the guidance contained in §232.15(f) and the requirements of this part or whether the alternative standard will provide at least an equivalent level of safety; and (4) A statement affirming that the railroad has served a copy of the petition on designated representatives of its employees, together with a list of the names and addresses of the persons served. (c) Petitions for special approval of pre-revenue service acceptance testing plan. Each petition for special approval of a pre-revenue service acceptance testing plan shall contain: (1) The name, title, address, and telephone number of the primary person to be contacted with regard to review of the petition; and (2) The elements prescribed in §232.505. (d) Service. (1) Each petition for special approval under paragraph (b) or (c) of this section shall be submitted in triplicate to the Associate Administrator for Safety, Federal Railroad Administration, 400 7th Street, SW., Washington, DC 20590. (2) Service of each petition for special approval of a plan or an alternative standard submitted under paragraph (b) of this section shall be made on the following: (i) Designated representatives of the employees of the railroad submitting a plan pursuant to §232.15(g) or designated representatives of the employees responsible for the equipment's operation, inspection, testing, and maintenance under this part; (ii) Any organizations or bodies that either issued the standard incorporated in the section(s) of the rule to which the special approval pertains or issued the alternative standard that is proposed in the petition; and (iii) Any other person who has filed with FRA a current statement of interest in reviewing special approvals under the particular requirement of this part at least 30 days but not more than 5 years prior to the filing of the petition. If filed, a statement of interest shall be filed with FRA's Associate Administrator for Safety and shall reference the specific section(s) of this part in which the person has an interest. (e) Federal Register notice. FRA will publish a notice in the (f) Comment. Not later than 30 days from the date of publication of the notice in the (1) A comment shall set forth specifically the basis upon which it is made, and contain a concise statement of the interest of the commenter in the proceeding. (2) The comment shall be submitted in triplicate to the Associate Administrator for Safety, Federal Railroad Administration, 400 7th Street, SW., Washington, DC 20590. (3) The commenter shall certify that a copy of the comment was served on each petitioner. (g) Disposition of petitions. (1) If FRA finds that the petition complies with the requirements of this section and that the proposed plan under §232.15(g), the alternative standard, or the pre-revenue service plan is acceptable and justified, the petition will be granted, normally within 90 days of its receipt. If the petition is neither granted nor denied within 90 days, the petition remains pending for decision. FRA may attach special conditions to the approval of any petition. Following the approval of a petition, FRA may reopen consideration of the petition for cause. (2) If FRA finds that the petition does not comply with the requirements of this section and that the proposed plan under §232.15(g), the alternative standard, or the pre-revenue service plan is not acceptable or justified, the petition will be denied, normally within 90 days of its receipt. (3) When FRA grants or denies a petition, or reopens consideration of the petition, written notice is sent to the petitioner and other interested parties. [66 FR 4193, Jan. 17, 2001, as amended at 67 FR 17580, Apr. 10, 2002] Except as otherwise provided, the records and plans required by this part shall be made available to representatives of FRA and States participating under part 212 of this chapter for inspection and copying upon request. (a) The information collection requirements of this part were reviewed by the Office of Management and Budget pursuant to the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.) and are assigned OMB control number 2130–0008. (b) The information collection requirements are found in the following sections: §§229.27, 231.31, 232.1, 232.3, 232.7, 232.11, 232.15, 232.17, 232.103, 232.105, 232.107, 232.109, 232.111, 232.203, 232.205, 232.207, 232.209, 232.211, 232.213, 232.303, 232.307, 232.309, 232.403, 232.405, 232.407, 232.409, 232.503, 232.505.
Title 49: Transportation
PART 232—BRAKE SYSTEM SAFETY STANDARDS for FREIGHT and OTHER NON-PASSENGER TRAINS and EQUIPMENT; END-of-TRAIN DEVICES
Subpart A—General
§ 232.1 Scope.
§ 232.3 Applicability.
§ 232.5 Definitions.
§ 232.7 Waivers.
§ 232.9 Responsibility for compliance.
§ 232.11 Penalties.
§ 232.13 Preemptive effect.
§ 232.15 Movement of defective equipment.
§ 232.17 Special approval procedure.
§ 232.19 Availability of records.
§ 232.21 Information Collection.
