30 C.F.R. § 250.198 Documents incorporated by reference.
Title 30 - Mineral Resources
Link to an amendment published at 71 FR 40911, July 19, 2006. (a) MMS is incorporating by reference the documents listed in the table in paragraph (e) of this section. The Director of the Federal Register has approved this incorporation by reference according to 5 U.S.C. 552(a) and 1 CFR part 51. (1) MMS will publish any changes to these documents in the (2) MMS may make the rule amending the document effective without prior opportunity for public comment when MMS determines: (i) That the revisions to a document result in safety improvements or represent new industry standard technology and do not impose undue costs on the affected parties; and (ii) MMS meets the requirements for making a rule immediately effective under 5 U.S.C. 553. (b) MMS incorporated each document or specific portion by reference in the sections noted. The entire document is incorporated by reference, unless the text of the corresponding sections in this part calls for compliance with specific portions of the listed documents. In each instance, the applicable document is the specific edition or specific edition and supplement or addendum cited in this section. (c) Under §§250.141 and 250.142, you may comply with a later edition of a specific document incorporated by reference, provided: (1) You show that complying with the later edition provides a degree of protection, safety, or performance equal to or better than would be achieved by compliance with the listed edition; and (2) You obtain the prior written approval for alternative compliance from the authorized MMS official. (d) You may inspect these documents at the Minerals Management Service, 381 Elden Street, Room 3313, Herndon, Virginia; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.php. You may obtain the documents from the publishing organizations at the addresses given in the following table: (e) This paragraph lists documents incorporated by reference. To easily reference text of the corresponding sections with the list of documents incorporated by reference, the list is in alphanumerical order by organization and document. [64 FR 72775, Dec. 28, 1999, as amended at 65 FR 218, 219, Jan. 4, 2000; 65 FR 3127, Jan. 20, 2000; 65 FR 14470, Mar. 17, 2000; 65 FR 15863, Mar. 24, 2000; 65 FR 18432, Apr. 7, 2000; 65 FR 25285, May 1, 2000; 65 FR 36328, June 8, 2000; 65 FR 40052, June 29, 2000; 65 FR 41002, July 3, 2000; 65 FR 76935, Dec. 8, 2000; 67 FR 51759, Aug. 9, 2002; 68 FR 46, Jan. 2, 2003; 68 FR 7427, Feb. 14, 2003; 68 FR 8422, Feb. 20, 2003; 68 FR 19355, Apr. 21, 2003; 68 FR 43298, July 22, 2003; 69 FR 18803, Apr. 9, 2004; 70 FR 7403, Feb. 14, 2005; 70 FR 41573, July 19, 2005]
Title 30: Mineral Resources
PART 250—OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF
Subpart A—General
References
§ 250.198 Documents incorporated by reference.
------------------------------------------------------------------------ For Write to------------------------------------------------------------------------ACI Standards..................... American Concrete Institute, P. O. Box 19150, Detroit, MI 48219.AISC Standards.................... American Institute of Steel Construction, Inc., P.O. Box 4588, Chicago, IL 60680.ANSI/ASME Codes................... American National Standards Institute, Attention Sales Department, 25 West 43rd Street, 4th Floor, New York, NY 10036; and/ or American Society of Mechanical Engineers, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007.API Recommended Practices, Specs, American Petroleum Institute, 1220 L Standards, Manual of Petroleum Street, NW., Washington, DC 20005- Measurement Standards (MPMS) 4070. chapters.ASTM Standards.................... American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.AWS Codes......................... American Welding Society, 550 NW, LeJeune Road, P.O. Box 351040, Miami, FL 33135.NACE Standards.................... National Association of Corrosion Engineers, P.O. Box 218340, Houston, TX 77218.------------------------------------------------------------------------
------------------------------------------------------------------------ Incorporated by reference Title of documents at------------------------------------------------------------------------ACI Standard 318-95, Building Code § 250.901(a)(1). Requirements for Reinforced Concrete, plus Commentary on Building Code Requirements for Reinforced Concrete (ACI 318R-95).ACI 357R-84, Guide for the Design and § 250.901(a)(2). Construction of Fixed Offshore Concrete Structures, 1984.AISC Standard Specification for Structural § 250.901(a)(3). Steel Buildings, Allowable Stress Design and Plastic Design, June 1, 1989, with Commentary.ANSI/ASME Boiler and Pressure Vessel Code, § 250.803(b)(1), Section I, Rules for Construction of Power (b)(1)(i); § Boilers, including Appendices, 1998 Edition; 250.1629(b)(1), July 1, 1999 Addenda, Rules for Construction (b)(1)(i). of Power Boilers, by ASME Boiler and Pressure Vessel Committee Subcommittee on Power Boilers; and all Section I Interpretations Volume 43.ANSI/ASME Boiler and Pressure Vessel Code, § 250.803(b)(1), Section IV, Rules for Construction of (b)(1)(i); § Heating Boilers, including Nonmandatory 250.1629(b)(1), Appendices A, B, C, D, E, F, H, I, K, and L, (b)(1)(i). and the Guide to Manufacturers Data Report Forms, 1998 Edition; July 1, 1999 Addenda, Rules for Construction of Heating Boilers, by ASME Boiler and Pressure Vessel Committee Subcommittee on Heating Boilers; and all Section IV Interpretations Volumes 43 and 44.ANSI/ASME Boiler and Pressure Vessel Code, § 250.803(b)(1), Section VIII, Rules for Construction of (b)(1)(i); § Pressure Vessels, Divisions 1 and 2, 250.1629(b)(1), including Nonmandatory Appendices, 1998 (b)(1)(i). Edition; July 1, 1999 Addenda, Rules for Construction of Pressure Vessels, by ASME Boiler and Pressure Vessel Committee Subcommittee on Pressure Vessels; and all Section VIII Interpretations, Divisions 1 and 2, Volumes 43 and 44.ANSI/ASME B 16.5-1988 (including Errata) and § 250.1002(b)(2). B 16.5a-1992 Addenda, Pipe Flanges and Flanged Fittings.ANSI/ASME B 31.8-1995, Gas Transmission and § 250.1002(a). Distribution Piping Systems.ANSI/ASME SPPE-1-1994 and SPPE-1d-1996 § 250.806(a)(2)(i). ADDENDA, Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations.ANSI Z88.2-1992, American National Standard § 250.490(g)(4)(iv), for Respiratory Protection. (j)(13)(ii).API 510, Pressure Vessel Inspection Code: § 250.803(b)(1). Maintenance Inspection, Rating, Repair, and § 250.1629(b)(1). Alteration, except for Sections 6.5 and 8.5, Eighth Edition, June 1997, API Stock No. C51008.API MPMS, Chapter 1, Vocabulary, Second § 250.1201. Edition, July 1994, API Stock No., H01002..API MPMS, Chapter 2, Tank Calibration, § 250.1202(l)(4). Section 2A, Measurement and Calibration of Upright Cylindrical Tanks by the Manual Strapping Method, First Edition, February 1995, API Stock No. H022A1.API MPMS, Chapter 2, Section 2B, Calibration 250.1202(l)(4). of Upright Cylindrical Tanks Using the Optical Reference Line Method, First Edition, March 1989, reaffirmed May 1996, API Stock No. H30023; also available as ANSI/ ASTM D 4738-88.API MPMS, Chapter 3, Tank Gauging, Section § 250.1202(l)(4). 1A, Standard Practice for the Manual Gauging of Petroleum and Petroleum Products, First Edition, December 1994, API Stock No. H031A1.API MPMS, Chapter 3, Section 1B, Standard § 250.1202(l)(4). Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic Tank Gauging, First Edition, April 1992, reaffirmed January 1997, API Stock No. H30060.API MPMS, Chapter 4, Proving Systems, Section § 250.1202(a)(3), 1, Introduction, First Edition, July 1988, (f)(1). reaffirmed October 1993, API Stock No. H30081.API MPMS, Chapter 4, Section 2, Conventional § 250.1202(a)(3), Pipe Provers, First Edition, October 1988, (f)(1). reaffirmed October 1993, API Stock No. H30082.API MPMS, Chapter 4, Section 3, Small Volume § 250.1202(a)(3), Provers, First Edition, July 1988, (f)(1). reaffirmed October 1993, API Stock No. H30083.API MPMS, Chapter 4, Section 4, Tank Provers, § 250.1202(a)(3), First Edition, October 1988, reaffirmed (f)(1). October 1993, API Stock No. H30084.API MPMS, Chapter 4, Section 5, Master-Meter § 250.1202(a)(3), Provers, First Edition, October 1988, (f)(1). reaffirmed October 1993, API Stock No. H30085.API MPMS, Chapter 4, Section 6, Pulse § 250.1202(a)(3) and Interpolation, Second Edition, May 1999, API (f)(1). Stock No. H04062.API MPMS, Chapter 4, Section 7, Field § 250.1202(a)(3) and Standard Test Measures, Second Edition, (f)(1). December 1998, API Stock No. H04072.API MPMS, Chapter 5, Metering, Section 1, § 250.1202(a)(3). General Considerations for Measurement by Meters, Third Edition, September 1995, API Stock No. H05013.API MPMS, Chapter 5, Section 2, Measurement § 250.1202(a)(3). of Liquid Hydrocarbons by Displacement Meters, Second Edition, November 1987, reaffirmed January 1997, API Stock No. H30102.API MPMS, Chapter 5, Section 3, Measurement § 250.1202(a)(3). of Liquid Hydrocarbons by Turbine Meters, Third Edition, September 1995, API Stock No. H05033.API MPMS, Chapter 5, Section 4, Accessory § 250.1202(a)(3). Equipment for Liquid Meters, Third Edition, September 1995, with Errata, March 1996, API Stock No. H05043.API MPMS, Chapter 5, Section 5, Fidelity and § 250.1202(a)(3). Security of Flow Measurement Pulsed-Data Transmission Systems, First Edition, June 1982, reaffirmed January 1997, API Stock No. H30105.API MPMS, Chapter 6, Metering Assemblies, § 250.1202(a)(3). Section 1, Lease Automatic Custody Transfer (LACT) Systems, Second Edition, May 1991, reaffirmed July 1996, API Stock No. H30121.API MPMS, Chapter 6, Section 6, Pipeline § 250.1202(a)(3). Metering Systems, Second Edition, May 1991, reaffirmed July 1996, API Stock No. H30126.API MPMS, Chapter 6, Section 7, Metering § 250.1202(a)(3). Viscous Hydrocarbons, Second Edition, May 1991, reaffirmed July 1996, API Stock No. H30127.API MPMS, Chapter 7, Temperature § 250.1202(a)(3), Determination, Section 2, Dynamic (l)(4). Temperature Determination, Second Edition, March 1995, API Stock No. H07022.API MPMS, Chapter 7, Section 3, Static § 250.1202(a)(3), Temperature Determination Using Portable (l)(4). Electronic Thermometers, First Edition, July 1985, reaffirmed May 1996, API Stock No. H30143.API MPMS, Chapter 8, Sampling, Section 1, § 250.1202(b)(4)(i), Standard Practice for Manual Sampling of (l)(4). Petroleum and Petroleum Products, Third Edition, October 1995; also available as ANSI/ASTM D 4057-88, API Stock No. H30161.API MPMS, Chapter 8, Section 2, Standard § 250.1202(a)(3), Practice for Automatic Sampling of Liquid (l)(4). Petroleum and Petroleum Products, Second Edition, October 1995; also available as ANSI/ASTM D 4177, API Stock No. H30162.API MPMS, Chapter 9, Density Determination, § 250.1202(a)(3) and Section 1, Hydrometer Test Method for (l)(4). Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products, First Edition, June 1981, reaffirmed December 1998, API Stock No. H30181; also available as ANSI/ASTM D 1298.API MPMS, Chapter 9, Section 2, Pressure § 250.1202(a)(3) and Hydrometer Test Method for Density or (l)(4). Relative Density, First Edition, April 1982, reaffirmed December 1998, API Stock No. H30182.API MPMS, Chapter 10, Sediment and Water, § 250.1202(a)(3), Section 1, Determination of Sediment in (l)(4). Crude Oils and Fuel Oils by the Extraction Method, First Edition, April 1981, reaffirmed December 1993; also available as ANSI/ASTM D 473, API Stock No. H30201.API MPMS, Chapter 10, Section 2, § 250.1202(a)(3), Determination of Water in Crude Oil by (l)(4). Distillation Method, First Edition, April 1981, reaffirmed December 1993; also available as ANSI/ASTM D 4006, API Stock No. H30202.API MPMS, Chapter 10, Section 3, § 250.1202(a)(3), Determination of Water and Sediment in Crude (l)(4). Oil by the Centrifuge Method (Laboratory Procedure), First Edition, April 1981, reaffirmed December 1993; also available as ANSI/ASTM D 4007, API Stock No. H30203.API MPMS, Chapter 10, Section 4, § 250.1202(a)(3), Determination of Sediment and Water in Crude (l)(4). Oil by the Centrifuge Method (Field Procedure), Second Edition, May 1988, reaffirmed May 1998; also available as ANSI/ ASTM D 96, API Stock No. H30204.API MPMS, Chapter 10, Section 9, Standard § 250.1202(a)(3), Test Method for Water in Crude Oils by (l)(4). Coulometric Karl Fischer Titration, First Edition, November 1993, API Stock No. 852- 30210.API MPMS, Chapter 11.1, Volume Correction § 250.1202(a)(3), Factors, Volume 1, Table 5A_Generalized (g)(3) and (l)(4). Crude Oils and JP-4, Correction of Observed API Gravity to API Gravity at 60°F, and Table 6A_Generalized Crude Oils and JP-4, Correction of Volume to 60°F, against API Gravity 60°F, First Edition, August 1980, reaffirmed March 1997, API Stock No. H27000; also available as ANSI/ASTM D 1250.API MPMS, Chapter 11.2.1, Compressibility § 250.1202(a)(3), Factors for Hydrocarbons: 0-90° API (g)(4). Gravity Range, First Edition, August 1984, reaffirmed May 1996, API Stock No. H27300.API MPMS, Chapter 11.2.2, Compressibility § 250.1202(a)(3) and Factors for Hydrocarbons: 0.350-0.637 (g)(4). Relative Density (60°F/60°F) and - 50°F to 140°F Metering Temperature, Second Edition, October 1986, reaffirmed March 1997, API Stock No. H27307; also available as Gas Processors Association (GPA) 8286.API MPMS, Chapter 11, Physical Properties § 250.1202(a)(3). Data, Addendum to Section 2.2, Compressibility Factors for Hydrocarbons, Correlation of Vapor Pressure for Commercial Natural Gas Liquids, First Edition, December 1994, reaffirmed March 1997; also available as GPA TP-15, API Stock No. H27308.API MPMS, Chapter 11.2.3, Water Calibration § 250.1202(f)(1). of Volumetric Provers, First Edition, August 1984, reaffirmed, May 1996, API Stock No. H27310.API MPMS, Chapter 12, Calculation of § 250.1202(a)(3), Petroleum Quantities, Section 2, Calculation (g)(1), (g)(2). of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors, Including Parts 1 and 2, Second Edition, May 1995; also available as ANSI/API MPMS 12.2-1981, API Stock No. H30302.API MPMS, Chapter 14, Natural Gas Fluids § 250.1203(b)(2). Measurement, Section 3, Concentric Square- Edged Orifice Meters, Part 1, General Equations and Uncertainty Guidelines, Third Edition, September 1990, reaffirmed August 1995; also available as ANSI/API 2530, Part 1, 1991, API Stock No. H30350.API MPMS, Chapter 14, Section 3, Part 2, § 250.1203(b)(2). Specification and Installation Requirements, Third Edition, February 1991, reaffirmed May 1996, API Stock No. H30351; also available as ANSI/API 2530, 1991.API MPMS, Chapter 14, Section 3, Part 3, § 250.1203(b)(2). Natural Gas Applications, Third Edition, August 1992, reaffirmed December 1998, API Stock No. H30353; also available as ANS/API 2530, Part 3.API MPMS, Chapter 14, Section 5, Calculation § 250.1203(b)(2). of Gross Heating Value, Relative Density, and Compressibility Factor for Natural Gas Mixtures from Compositional Analysis, Revised 1996; order from Gas Processors Association, 6526 East 60th Street, Tulsa, Oklahoma 74145.API MPMS, Chapter 14, Section 6, Continuous § 250.1203(b)(2). Density Measurement, Second Edition, April 1991, reaffirmed May 1998, API Stock No. H30346.API MPMS, Chapter 14, Section 8, Liquefied § 250.1203(b)(2). Petroleum Gas Measurement, Second Edition, July 1997; reaffirmed May 1996, API Stock No. H14082.API MPMS, Chapter 20, Section 1, Allocation § 250.1202(k)(1). Measurement, First Edition, September 1993, API Stock No. H30730.API MPMS, Chapter 21, Section 1, Electronic § 250.1203(b)(4). Gas Measurement, First Edition, September 1993, API Stock No. H30730.API RP 2A-WSD, Recommended Practice for § 250.901(a)(4); Planning, Designing, and Constructing Fixed § 250.908(a); Offshore Platforms_Working Stress Design; § Twenty-first Edition, December 2000, API 250.920(a)(b)(c)(e). Order No. G2AWSD.API RP 2D, Recommended Practice for Operation § 250.108(a). and Maintenance of Offshore Cranes, Fourth Edition, August 1, 1999, API Stock No. G02D04.API RP 2FPS, Recommended Practice for § 250.901(a)(5). Planning, Designing, and Constructing Floating Production Systems, First Edition, March 2001, API Order No. G2FPS1.API RP 2RD, Design of Risers for Floating § 250.800(b); § Production Systems (FPSs) and Tension-Leg 250.901(a)(6); § Platforms (TLPs), First Edition, June 1998, 250.1002(b)(5). API Order No. G02RD1.API RP 2SK, Recommended Practice for Design § 250.800(b); § and Analysis of Stationkeeping Systems for 250.901(a)(7). Floating Structures, Second Edition, December 1996, Effective Date: March 1, 1997, API Order No. G02SK2.API RP 2SM, Recommended Practice for Design, § 250.901(a)(8). Manufacture, Installation, and Maintenance of Synthetic Fiber Ropes for Offshore Mooring, First Edition, March 2001, API Order No. G02SM1.API RP 2T, Planning, Designing and § 250.901(a)(9). Constructing Tension Leg Platforms, Second Edition, August 1997, API Order No. G02T02.API RP 14B, Recommended Practice for Design, § 250.801(e)(4); Installation, Repair and Operation of § 250.804(a)(1)(i). Subsurface Safety Valve Systems, Fourth Edition, July 1, 1994, with Errata dated June 1996, API Stock No. G14B04.API RP 14C, Recommended Practice for § 250.802(b), Analysis, Design, Installation, and Testing (e)(2); § of Basic Surface Safety Systems for Offshore 250.803(a), (b)(2)(i), Production Platforms, Seventh Edition, March (b)(4), (b)(5)(i), 2001, API Stock No. C14C07. (b)(7), (b)(9)(v), (c)(2); § 250.804(a), (a)(6); § 250.1002(d); § 250.1004(b)(9); § 250.1628(c), (d)(2); § 250.1629(b)(2), (b)(4)(v); and § 250.1630(a).API RP 14E, Recommended Practice for Design § 250.802(e)(3); and Installation of Offshore Production § 250.1628(b)(2), Platform Piping Systems, Fifth Edition, (d)(3). October 1, 1991, API Stock No. G07185.API RP 14F, Recommended Practice for Design § 250.114(c); and Installation of Electrical Systems for § 250.803(b)(9)(v); Fixed and Floating Offshore Petroleum § 250.1629(b)(4)(v). Facilities for Unclassified and Class I, Division 1 and Division 2 Locations, 4th edition, June 1999, API Stock No. G14F04.API RP 14FZ, Recommended Practice for Design § 250.114(c); and Installation of Electrical Systems for § 250.803(b)(9)(v); Fixed and Floating Offshore Petroleum § 250.1629(b)(4)(v). Facilities for Unclassified and Class I, Zone 0, Zone 1 and Zone 2 Locations, 1st edition, September 2001, API Stock No. G14FZ1.API RP 14G, Recommended Practice for Fire § 250.803(b)(8), Prevention and Control on Open Type Offshore (b)(9)(v); § Production Platforms, Third Edition, 250.1629(b)(3), December 1, 1993, API Stock No. G07194. (b)(4)(v).API RP 14H, Recommended Practice for the § 250.802(d); Installation, Maintenance and Repair of 250.804(a)(4). Surface Safety Valves and Underwater Safety Valves Offshore, Fourth Edition, July 1, 1994, API Stock No. G14H04.API RP 14J, Recommended Practice for Design § 250.800(b); § and Hazards Analysis for Offshore Production 250.901(a)(10). Facilities, Second Edition, May 2001, API Order No. G14J02.API RP 53, Recommended Practices for Blowout § 250.442(c); § Prevention Equipment Systems for Drilling 250.446(a). Wells, Third Edition, March 1997, API Stock No. G53003.API RP 500, Recommended Practice for § 250.114(a); § Classification of Locations for Electrical 250.459; § Installations at Petroleum Facilities, 250.802(e)(4)(i); § Classified as Class I, Division 1 and 250.803(b)(9)(i); § Division 2, Second Edition, November 1997, 250.1628(b)(3); API Stock No. C50002. (d)(4)(i); § 250.1629(b)(4)(i).API RP 505, Recommended Practice for § 250.114(a); § Classification of Locations for Electrical 250.459; § Installations at Petroleum Facilities, 250.802(e)(4)(i); § Classified as Class I, Zone 0, Zone 1, and 250.803(b)(9)(i); § Zone 2, First Edition, November 1997, API 250.1628(b)(3); Stock No. C50501. (d)(4)(i); § 250.1629(b)(4)(i).API RP 2556, Recommended Practice for § 250.1202(l)(4). Correcting Gauge Tables for Incrustation, Second Edition, August 1993, API Stock No. H25560; also available under the umbrella of the MPMS.API Spec Q1, Specification for Quality § 250.806(a)(2)(ii). Programs for the Petroleum and Natural Gas Industry, Sixth Edition, March 1, 1999. API Stock No. GQ1006.API Spec 2C, Specification for Offshore § 250.108(c) and Cranes, Fifth Edition, April 1, 1995, API (d). Stock No. G02C05.API Spec 6A, Specification for Wellhead and § 250.806(a)(3); Christmas Tree Equipment, Seventeenth § 250.1002 (b)(1), Edition, February 1, 1996, API Stock No. (b)(2). G06A17.API Spec 6AV1, Specification for Verification § 250.806(a)(3). Test of Wellhead Surface Safety Valves and Underwater Safety Valves for Offshore Service, First Edition, February 1, 1996, API Stock No. G06AV1.API Spec 6D, Specification for Pipeline § 250.1002(b)(1). Valves (Gate, Plug, Ball, and Check Valves), Twenty-first Edition, March 31, 1994, including Supplement 2, December 1, 1997, API Stock No. G03200.API Spec 14A, Tenth Edition, November 2000, § 250.806(a)(3). ISO10432:1999, Petroleum and Natural Gas Industries_Downhole Equipment_Subsurface Safety Valve Equipment, API Stock No. G14A09.API Spec 17J, Specification for Unbonded § Flexible Pipe, Second Edition, November 250.803(b)(2)(iii); 1999, including errata (May 25, 2001) and § 250.1002(b)(4); Addendum 1 (June 2003), Effective Date: § 250.1007(a)(4). December 2002, API Order No. G17J02.API Standard 2551, Standard Method for § 250.1202(l)(4). Measurement and Calibration of Horizontal Tanks, First Edition, 1965, reaffirmed January 1997; API Stock No. H25510; also available under the umbrella of the MPMS.API Standard 2552, Measurement and § 250.1202(l)(4). Calibration of Spheres and Spheroids, First Edition, 1966, reaffirmed January 1997, API Stock No. H25520; also available under the umbrella of the MPMS.API Standard 2555, Method for Liquid § 250.1202(l)(4). Calibration of Tanks, September 1966, reaffirmed January 1997, API Stock No. H25550; also available under the umbrella of the MPMS.ASTM Standard C 33-99a, Standard § 250.901(a)(11). Specification for Concrete Aggregates.ASTM Standard C 94/C 94M-99, Standard § 250.901(a)(12). Specification for Ready-Mixed Concrete.ASTM Standard C 150-99, Standard § 250.901(a)(13). Specification for Portland Cement.ASTM Standard C 330-99, Standard § 250.901(a)(14). Specification for Lightweight Aggregates for Structural Concrete.ASTM Standard C 595-98, Standard § 250.901(a)(15). Specification for Blended Hydraulic Cements.AWS D1.1-96, Structural Welding Code_Steel, § 250.901(a)(16). 1996, including Commentary.AWS D1.4-79, Structural Welding § 250.901(a)(17). Code_Reinforcing Steel, 1979.AWS D3.6M:1999, Specification for Underwater § 250.901(a)(18). Welding.NACE Standard MR0175-99, Sulfide Stress § 250.901(a)(19). Cracking Resistant Metallic Materials for Oilfield Equipment, Revised January 1999, NACE Item No. 21302.NACE Standard RP 01-76-94, Standard § 250.901(a)(20). Recommended Practice, Corrosion Control of Steel Fixed Offshore Platforms Associated with Petroleum Production.------------------------------------------------------------------------
